2026-03-13

Répétiteur latéral - avant - gauche (HW4) (retrait et remplacement)

Code de correction 17221302 0.24 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. NOTE : Consultez Protection individuelle pour veiller à porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

  • 2026-03-02: Updated calibration steps to use ServiceUI.
  • 2024-02-05: Ajout d'un avertissement pour envelopper les bornes de la camera et du faisceau de câbles pour éviter qu'elles n'entrent en contact avec de l'eau ou d'autres solutions susceptibles de les endommager.
  • 2023-04-19: Added HW4 camera connection test steps.

Retirer

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  1. Open the LH front door.
  2. Lower LH front window.
  3. Press the brake pedal to turn on the drive rails.
  4. Use the center display to set the air suspension ride height to “Very High”.
  5. Turn the steering wheel fully to the left.
  6. Enable service mode. See Mode entretien (activer et désactiver).
  7. Apply masking tape to the LH front fender assembly at the edges of the LH front side repeater.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Masking tape
  8. Partially remove the rear portion of the LH front wheel arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Insert a plastic trim tool between the edge of the wheel liner and back of the fender, and then open a portion of the wheel liner to gain access to the side repeater assembly.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Plastic trim tool
  9. Release the push clip that attaches the LH front side repeater to the LH front fender assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Push the repeater locator tab to release the repeater from the fender, guide the locator tab to clear the fender, and then remove the repeater from the fender.
  10. Disconnect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Press down on the lock release and pull the connector away from the side repeater camera. Release the red locking tab and press down to disconnect the side repeater connector.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Enveloppez les bornes de la camera et du faisceau de câbles pour éviter qu'elles n'entrent en contact avec de l'eau ou d'autres solutions susceptibles de les endommager.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Pocket screwdriver
  11. Remove the LH front side repeater from the vehicle.
  12. Remove the bolts (x2) that attach the LH front side repeater camera to the repeater assembly, and then remove the camera from the repeater assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove the bolts and then wiggle the camera to clear the o-ring from the repeater assembly.

Installer

  1. Position the LH front side repeater camera on the repeater assembly, and then install the bolts (x2) that attach the camera on the repeater assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Wiggle the camera o-ring through the repeater assembly, and then install that bolts that attach the camera to the repeater assembly.
  2. Connect the LH front side repeater connectors (x2).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove the tape first, if present.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Secure the side repeater connectors, and then engage the red locking tab on the side repeater connector.
  3. Réinitialisez le système d'assistance conducteur (DAS).
    1. Déverrouillez la passerelle du véhicule. Voir Passerelle (déverrouiller),
    2. Dans le menu du mode Entretien de l’écran tactile, touchez Assistance conducteur > Caméras > Réinitialiser DAS.
    3. Sur le diagramme des caméras de l'écran tactile, vérifiez que le bouton Réinitialiser le DAS est surligné en vert et que tous les composants du DAS affichent un voyant d'état vert.
      Informational PurposesAn informational icon, calling your attention
      Remarque
      Vérifiez et corrigez tout composant DAS illuminé en rouge.
  4. Unlock the vehicle gateway. See .
  5. Run PROC_DAS_X_CLEAR-CALIBRATIONvia Service Mode:
    • Driver Assist ➜ Cameras ➜ Clear Camera Calibration
    • Driver Assist ➜ Driverless ➜ Clear Calibration
    via Toolbox:(link)
  6. Run PROC_DAS_X_UPDATE-CAMERAvia Service Mode:Driver Assist ➜ Cameras ➜ Update Cameravia Toolbox:(link)
  7. Install the push clip that attaches the LH front side repeater to the LH front fender assembly.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure all tabs are intact and installed in place correctly.
    1. Insert the side repeater rear hook clip into the repeater slot in the fender, apply light constant pressure at the rear of the repeater, and then keep pressure until the repeater is installed.
    2. Slide the side repeater rearwards until the rear hook clip engages the fender and the front clip clears the edge of the repeater slot in the fender.
    3. Press on the front of the side repeater until the front clip is inside of the repeater slot and keep pressure on the front and rear of the repeater until installation is complete.
    4. Slide the side repeater towards the front of the vehicle until the front clip engages the fender, and then release pressure on the repeater.
  8. Remove the masking tape from the LH front fender assembly at the edges of the LH front side repeater.
  9. Push the rear portion of the LH front wheel arch liner back to original position.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure the liner aligns with the fender correctly.
  10. Press the brake pedal to turn on the drive rails.
  11. Turn the steering wheel to the center.
  12. Use the center display to set the air suspension ride height to “Medium”.
  13. Disable service mode. See Mode entretien (activer et désactiver).
  14. Raise the LH front window.
  15. Close the LH front door.