2024-06-17

Fusible - système de conversion d’énergie - batterie HT (retirez et remplacez)

Code de correction 16304402 5.16 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Retirer

  1. Move the vehicle to a 2 post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.
  2. Perform a cooling system thermal fill drain. See Fluide thermique - système de refroidissement (remplissage/vidange).
  3. Remove the LH and RH rocker panel scuff plates. See Plaque d’usure – bas de caisse – gauche (retrait et remplacement).
  4. Remove the LH and RH rocker panel moldings. See Moulure – bas de caisse – gauche (retrait et remplacement).
  5. Position the 2 post lift pads for HV battery removal.
  6. Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  7. Déconnectez l’alimentation basse tension. Voir Alimentation 12 BT (déconnecter et connecter).
  8. Remove the mid aero shield panel. See Panneau - écran aérodynamique - central (retirez et remplacez). .
  9. Effectuez la procédure de désactivation HT du véhicule. Voir Procédure de désactivation HT du véhicule.
  10. Retirez le sectionneur de batterie pyro. Voir Sectionneur de batterie pyrotechnique (retirez et remplacez).
  11. Remove the HV Battery. See Batterie HT (AWD) (retirez et installez).
  12. Release the clip that attaches the power conversion system outlet hose to the HV battery.
  13. Release the clip that attaches the power conversion system outlet hose to the to the HV battery fitting, and then disconnect the hose from the HV battery.
  14. Perform a power conversion system coolant drain. See Liquide de refroidissement du système de conversion de puissance (vidange) (Sur table).
  15. Remove the HV battery front access cover. See Couvercle - accès avant - batterie HT (retrait et installation).
  16. Remove the power conversion system. See Système de conversion d’énergie (retirez et remplacez).
  17. Remove the bolts (x6) that attach the power conversion system mounting tray to the HV battery, and then remove the tray from the HV battery.
  18. Remove the nuts (x2) that attach the power conversion system fuse to the mounting studs.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x nuts, 8mm, 2.5 Nm
  19. Remove the electrical harness terminal from the mounting stud and move aside.
  20. Use the fuse puller to remove the power conversion system fuse from the mounting studs.

Installer

  1. Perform a zero adjust of the Hioki resistance meter in preparation to measure resistances later in this procedure. See Compteur de résistance (réglage zéro).
  2. Use the fuse puller to install the power conversion system fuse onro the mounting studs.
  3. Install the electrical harness terminal onto the mounting stud.
  4. Install the nuts (x2) that attach the power conversion fuse to the mounting studs.
    2.5 Nm (1.8 lbs-ft)
  5. Use the Hioki resistance meter to measure the resistance at the HV joint of the power conversion system fuse and the positive DC busbar.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not short the side of the probe tip to the edge of the fuse lug.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance must be less than 0.145 mΩ (145 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
  6. Use the Hioki resistance meter to measure the resistance at the HV joint of the power conversion system fuse and the electrical harness terminal.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Do not short the side of the probe tip to the edge of the electrical harness terminal or the nut's captive washer.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The resistance must be less than 0.145 mΩ (145 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
  7. Install the power conversion system mounting tray into the HV battery, and then install the bolts (x6) that attach the tray to the HV battery.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure that no wires are pinched beneath the tray.
  8. Install the power conversion system. See Système de conversion d’énergie (retirez et remplacez).
  9. Install the HV battery front access cover. See Couvercle - accès avant - batterie HT (retrait et installation).
  10. Mesurez la tension à travers les points de montage de déconnexion de la batterie pyrotechnique puis installez la déconnexion de la batterie pyrotechnique Voir Sectionneur de batterie pyrotechnique (retirez et remplacez).
  11. Perform a power conversion system coolant leak test. See Test de fuite de liquide de refroidissement du système de conversion de puissance (sur la table).
  12. Perform an HV battery air leak test. See Test de fuite d'air de la batterie HT (sur la table).
  13. Install the HV Battery. See Batterie HT (AWD) (retirez et installez).
  14. Install the mid aero shield panel. See Panneau - écran aérodynamique - central (retirez et remplacez).
  15. Branchez l'alimentation BT. Voir Alimentation 12 BT (déconnecter et connecter).
  16. Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  17. Install the LH and RH rocker panel moldings. See Moulure – bas de caisse – gauche (retrait et remplacement).
  18. Install the LH and RH rocker panel scuff plates. See Plaque d’usure – bas de caisse – gauche (retrait et remplacement).
  19. Remove the vehicle from the 2 post lift. See Soulever le véhicule - pont élévateur à 2 poteaux.