2024-06-17

Ensemble de porte - port de charge (international) (retrait et remplacement)

Code de correction 44011512 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

  • 2024-04-04: Added the installation step of the busbar to the charge port nuts.
  • 2023-07-06: Cleaned up procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Retirez tous vos bijoux (montres, bracelets, bagues, colliers, boucles d’oreilles, étiquettes d’identification, piercings, etc.) et tous les objets (clés, pièces de monnaie, stylos, crayons, outils, attaches, etc.) de vos poches avant d’effectuer toute procédure vous exposant à un courant haute tension.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Si une procédure exige que vous portiez des verres protecteurs, assurez-vous que ces derniers sont bien retenus à votre tête et qu’ils ne peuvent pas tomber.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement

Seuls les techniciens qui ont été sensibilisés aux dangers de la haute tension et qui ont complété toutes les formations de certification requises (le cas échéant) sont autorisés à effectuer cette procédure. Portez toujours un équipement de protection personnelle et des gants isolants haute tension ayant un classement minimal de 0 (1000 volts) avant de manipuler un câble, une barre omnibus ou des raccords haute tension. Reportez-vous à la note technique TN-15-92-003, Mises en garde relatives à la haute tension pour obtenir des renseignements supplémentaires sur les gants et la sécurité.

Informational PurposesAn informational icon, calling your attention
Remarque
Cette procédure concerne la version Global Refresh de cette pièce. La procédure pour la version originale de cette pièce est ici : Porte - port de recharge (ND) (retirez et remplacez).

Retirer

  1. Ouvrez la porte avant gauche et abaissez la vitre avant gauche.
  2. Ouvrez la porte avant gauche et abaissez la vitre arrière gauche.
  3. Fold the LH 2nd row 60 seat down.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Seat can be folded from the backrest button or trunk switch.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Since the seat cushion is not present, protect the seat as required.
  4. Open the liftgate.
  5. Remove the rear trunk parcel shelf. See Plage arrière - coffre arrière (retrait et remplacement).
  6. Remove the rear trunk load floor. See Plancher de chargement du coffre - arrière (retirez et remplacez).
  7. Remove the side trunk load floor. See Plancher de chargement du coffre - latéral (retrait et remplacement).
  8. Remove the trunk sill trim. See Garniture - seuil - coffre (retrait et remplacement).
  9. Open the charge port door using the vehicle touchscreen.
  10. Open the hood.
  11. Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  12. Disconnect LV power. See Alimentation 12 BT (déconnecter et connecter).
  13. Perform the charge port voltage check. See Vérification de la tension du port de recharge.
  14. Remove the rear wall rear trunk trim. See Garniture - coffre arrière - paroi arrière (retrait et remplacement).
  15. Remove the LH trunk load floor bracket. See Bride - plancher de chargement du coffre - gauche (retirez et remplacez).
  16. Remove the trunk floor front trim. See Garniture - avant - plancher - coffre (retrait et remplacement).
  17. Remove the LH 2nd row seat outer bolster. See Traversin - externe - siège - seconde rangée - gauche (retrait et remplacement).
  18. Release the LH upper C-pillar trim, and then set it aside. See Garniture - montant arrière - supérieure - gauche (retirez et remplacez).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Do not remove the lower bolt that attaches the LH 2nd row seat belt retractor.
  19. Remove the LH trunk side trim. See Garniture – latérale – coffre – gauche (retrait et remplacement).
  20. Remove the LH taillight. See Feu arrière – gauche (international) (retrait et remplacement).
  21. Disconnect the charge port latch electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Take note of harness routing.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull the red locking tab outwards to release the lock, and then pull again to release the electrical connector.
  22. Disconnect the charge port electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Carefully remove the white locking tab. Press the tab to release the electrical connector from the charge port. Continue to pull off the connector. The connector is intended to disengage the safety cap when released.
  23. Remove the charge port to HV battery busbar safety cap. See Capuchon de sécurité - barre omnibus - entre le port de recharge et la batterie HT (international) (retrait et remplacement).
  24. Remove the nuts (x2) that attach the charge port busbars to the charge port, and then remove the busbar leads from the studs.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 11 mm
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nuts have captured washers.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Take caution of any tension present with the busbars.
  25. Remove the charge port. See Port de recharge (international) (retrait et remplacement).
  26. Disconnect the charge port door connection from the charge port ECU.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Take note of the original harness routing.
  27. Release the charge port door harness grommet from the body.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the grommet and feed harness out.
  28. Remove the bolt that attaches the charge port door to the body.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille longue de 8 mm
  29. Remove the charge port door assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x3 datums
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Release the single datum from vehicle body. Maneuver the charge port door assembly and motor out from the rear of vehicle and guide the harness out.

Installer

  1. Install the charge port door assembly to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x3 datums
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Guide the harness in, then maneuver the charge port door assembly and motor in from the rear of vehicle. Secure the single datum onto the body.
  2. Install the bolt that attaches the charge port door to the body.
    1 Nm (.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille longue de 8 mm
  3. Fully secure the charge port door harness grommet onto the body.
  4. Connect the charge port door electrical connector onto the charge port ECU.
  5. Install the charge port assembly into the vehicle and attach bolts (x4).
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 10 mm
    Informational PurposesAn informational icon, calling your attention
    Remarque
    x2 datums.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Start by lining up the datums on the charge port with the charge port door, and then proceed to thread in all bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    New charge port will come pre-applied with Penetrox.
  6. Secure the charge port manual release cable onto the body.
  7. Verify that the charge port studs (x2) are tightened to specification.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Embout Torx T10
  8. Clean the charge port assembly busbar contact surface of residual Penetrox with an IPA wipe.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use a plastic trim tool to push the IPA wipe down between plastic divider.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Allow 1 minute dry time after removing the Penetrox.
  9. Clean the charge port busbar contact surface of residual Penetrox.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Allow 1 minute dry time.
  10. Apply Penetrox to the backside of the busbar leads.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Apply 2 drops of Penetrox A-13 about 5 mm in diameter to either side of the hole on both leads. Spread evenly to verify the contact surface is fully covered.
  11. Install the nuts (x2) that attach the charge port busbars to the charge port.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Nous recommandons l’utilisation des outils suivants :
    • Douille de 11 mm
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nuts have captured washers.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If excessive force is required to seat the busbars, they may have been bent. Inspect for damage and replace if necessary.
  12. Inspect HV insulating gloves.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Check gloves for damage prior to use. Refer to service document TN-15-92-003 for information on inspecting HV gloves: https://service.tesla.com/user/documents?searchText=TN-15-92-003
  13. Put on the HV insulating gloves and leather over gloves.
  14. Perform a Hioki resistance test at each HV joint from the HV busbar lead to the charge port stud (x2 HV joints).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    When using the Hioki tester, verify that the meter has been properly adjusted and set prior to usage.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.270 mΩ (270 μΩ).
    • If the resistance is greater than 0.270 mΩ (270 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.
    • If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.
    • If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), the Hioki resistance test passed. Proceed to next step.
  15. Remove the leather glove protectors and HV insulating gloves.
  16. Install the busbar safety cap. See Capuchon de sécurité - barre omnibus - entre le port de recharge et la batterie HT (international) (retrait et remplacement).
  17. Connect the charge port electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fully engage the electrical connector and white locking tab. The connector is intended to lock the safety cap in place.
  18. Connect the charge port latch electrical connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Return the harness to its original routing: Harness sits in front of the busbars.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fully engage the connector and red locking tab.
  19. Install the LH taillight. See Feu arrière – gauche (international) (retrait et remplacement).
  20. Install the LH trunk side trim. See Garniture – latérale – coffre – gauche (retrait et remplacement).
  21. Install the LH upper C-pillar trim. See Garniture - montant arrière - supérieure - gauche (retirez et remplacez).
  22. Install the LH 2nd row seat outer bolster. See Traversin - externe - siège - seconde rangée - gauche (retrait et remplacement).
  23. Install the trunk floor front trim. See Garniture - avant - plancher - coffre (retrait et remplacement).
  24. Install the LH trunk load floor bracket. See Bride - plancher de chargement du coffre - gauche (retirez et remplacez).
  25. Install the rear wall rear trunk trim. See Garniture - coffre arrière - paroi arrière (retrait et remplacement).
  26. Install the trunk sill trim. See Garniture - seuil - coffre (retrait et remplacement).
  27. Install the side trunk load floor. See Plancher de chargement du coffre - latéral (retrait et remplacement).
  28. Install the rear trunk load floor. See Plancher de chargement du coffre - arrière (retirez et remplacez).
  29. Install the rear trunk parcel shelf. See Plage arrière - coffre arrière (retrait et remplacement).
  30. Close the liftgate.
  31. Restore the LH 2nd row 60 seat into upright position.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Remove seat cushion protection.
  32. Remontez la vitre arrière gauche et fermez la porte arrière gauche.
  33. Reconnect LV power. See Alimentation 12 BT (déconnecter et connecter).
  34. Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
  35. Close the hood.
  36. Verify operation of the vehicle charging system.
  37. Close the charge port door.
  38. Remontez la vitre avant gauche et fermez la porte avant gauche.