2026-07-31

Coax Cable - Side Repeater - Front - RH (Overlay) (Remove and Replace)

Code de correction 17403112 FRT 1.38 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.
  • 2026-07-09: Released new procedure.

Overlay

  1. Open both front doors and lower both front windows.
  2. Remove the wiper module. See Module d’essuie-glace (retirez et remplacez).
  3. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 2x tabs
  4. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, Partially release seal if needed
  5. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x magnets, 1x connector, 4x datums
  6. Move RH front seat backward
  7. Remove RH front floor mat
  8. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips
  9. Fold RH front cabin carpet aside for access
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Caution not to damage styrofoam of carpet
  10. Release harness from RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  11. Remove RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  12. Disconnect brown fakra connection from car computer
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, X836
  13. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  14. Remove RH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift every other spoke at a time until cap is released from rim
  15. Loosen RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x nuts, 21mm, 175 Nm
  16. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  17. Remove RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x nuts, 21mm, 175 Nm
  18. Partially release rear portion of RH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 1x fan clip, Move liner aside
  19. Disconnect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  20. Release RH grommet from body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
  21. Remove electrical tape securing harness bundle to rubber dust boot
  22. Remove the connector from the coax cable
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
  23. Apply harness tape onto RH coax overlay cable before installation
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  24. Position RH coax overlay cable into place, Place through RH wheel liner and dust boot towards interior cabin
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  25. Pull RH coax overlay cable through bulkhead and into interior cabin
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Pull harness toward car over car computer
  26. Position RH coax overlay cable onto harness, Secure cable onto car computer harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x zip-ties, Trim off excess material after harness has been secured
  27. Secure coax overlay through RH wheel liner and frunk harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x zip-ties, Trim off excess material after harness has been secured
  28. Depin the RH side coax cable (Terminal 1) from the connector X846
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  29. Remove the coax cable from the Connector X846
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
  30. Insert coax overlay terminal into connector X846
  31. Insert the connector locking tab and reconnect X846 together
  32. Connect brown fakra connection onto car computer
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, X836
  33. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Cut the coax connector only
  34. Connect RH front repeater
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  35. Secure RH grommet onto body
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use electrical tape to wrap the end of the dust boot
  36. Secure rear portion of RH rear wheel liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips, 1x fan clip, Secure liner
  37. Install RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  38. Lower vehicle until tires are touching ground
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  39. Torque RH front wheel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x nuts, 21mm, 175 Nm
  40. Install RH front wheel cap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Align valve stem with cap
  41. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  42. Install RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
  43. Secure harness to RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  44. Fold RH main carpet back into place
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Caution not to damage styrofoam of carpet
  45. Install RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips
  46. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x magnets, 4x datums, 1x connector
  47. Install RH front floor mat
  48. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x clips, Verify weather seal is seated properly
  49. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 2x tabs, Verify weather seal is seated properly
  50. Move RH front seat to original position
  51. Install the wiper module. See Module d’essuie-glace (retirez et remplacez).
  52. Unlock the vehicle gateway. See Passerelle (déverrouiller).
  53. Reset DAS on UI
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
  54. Exit Service Mode.
  55. Raise both front windows and close both front doors.