2025-06-23

Bed Side Wall - Upper - LH (Long Range) (Remove and Install)

Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.
  • 2025-06-21: Released new procedure.
  1. Open tailgate
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press button to release
  2. Remove fastener covers from bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    14x covers
  3. Remove bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
  4. Remove LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Nota
    15x clips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip
  5. Remove LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    13x clips, Start from rear, Pull from the bottom downwards
  6. Remove LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle
  7. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  8. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers
  9. Install LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    6x clips, 1x tab, Secure LH tailgate cable once closeout installed
  10. Install LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    13x clips, Replace any missing or damaged clips, Lift tonneau seal as required
  11. Install LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Nota
    15x clips, 1x connector, 1x harness clip, Replace any broken clips
  12. Install RH sail applique
    Informational PurposesAn informational icon, calling your attention
    Nota
    13x clips, Replace any damaged clips
  13. Install bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
  14. Install fastener covers onto bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    14x covers
  15. Close tailgate