2026-05-27

Bed Side Wall - LH (Standard) (Remove and Install)

Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-05-08: Released new procedure.
  1. Abra la cubierta de la plataforma de carga.
  2. Abra el portón trasero.
  3. Abra la puerta delantera izquierda y baje la ventanilla.
  4. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
  5. Remove the LH sail applique. See Sail Applique - RH (Remove and Install) (Post 11/4/2024).
  6. Remove the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install)
  7. Remove the upper bedside wall assembly. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
  8. Remove the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
  9. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 3x connectorsRelease locking tabs, Disconnect bed outlet connectors from bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Release locking tabs, Slide lock to release.
  10. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 15mm, 46 Nm, 2x bolts, 13mm, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Secure locking tabs, Connect bed outlet connectors onto bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Secure locking tabs, Slide lock to secure, Recommend assistance
  11. Install the LH rear bed closeout. See Bed Closeout - Rear - LH (Remove and Install).
  12. Install the upper bedside wall assembly. See Bed Side Wall Assembly - Upper - LH (Remove and Install).
  13. Install the LH tonneau water management seal. See Water Management Seal - LH - Center - Tonneau (Remove and Install)
  14. Install the LH sail applique. See Sail Applique - RH (Remove and Install) (Post 11/4/2024).
  15. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).