2026-04-16

Stud Plate - Hinge - Upper - Door - Rear - LH (Remove and Install)

Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Los componentes electrónicos del Cybertruck están alimentados por una arquitectura de media tensión de 48 V diseñada para mejorar la eficiencia. El mantenimiento de los componentes de media tensión requiere un conocimiento y cuidado adicionales para evitar daños personales o en el vehículo. Lea y comprenda las precauciones relacionadas con la media tensión en Precauciones eléctricas y asegúrese de realizar todos los cursos de formación necesarios, según corresponda.
  • 2026-03-31: Released new procedure.
  1. Remove the LH rear door window regulator. See Window Regulator - Rear Door - LH (Remove and Install).
  2. Apply masking tape around the LH upper rear door hinge
  3. Use a floor jack to support the LH rear door.Raise the jack until it contacts the door.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Place a folded microfiber towel or rubber pad between jack pad to protect the door.
  4. Remove LH rear door upper hinge plate
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x nuts, 10mm, 10Nm, 1x nut, 15mm, 38Nm
  5. Install LH upper rear door hinge plate and remove tape
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x nuts, 10mm, 10Nm, 1x nut, 15mm, 38Nm
  6. Install LH rear door closeout panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    11x bolts, 8mm, 4 Nm, 2x bolts,10mm, 12 Nm, 2x grommets
  7. Secure LH rear door harness onto close out panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    5x clips, 4x connectors
  8. Connect external window switch
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector
  9. Install LH rear door glass
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 4 Nm, Torque at later step, Make sure to properly secure onto regulator mount
  10. Manually unlatch LH rear door
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pull on the emergency cable to unlatch, If applicable
  11. Vuelva a conectar la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
  12. Abra la puerta trasera izquierda.
  13. Check LH rear door gap and flushness
    Informational PurposesAn informational icon, calling your attention
    Nota
    Verify door alignment, and adjust if needed.
  14. Check gap and flushness of LH rear window
  15. Open LH rear door
    Informational PurposesAn informational icon, calling your attention
    Nota
    Push LH C-pillar door trigger to release
  16. Torque bolts securing LH rear window to regulator
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 13 Nm
  17. Disconnect external window switch
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector
  18. Install the LH rear door inner waist belt seal. See Waist Belt Seal - Inner - Rear Door - LH (Remove and Install).
  19. Install the LH rear door trim. See Panel - Door Trim - Rear - LH (Remove and Install).
  20. Install the LH rear door beltline assembly. See Beltline Assembly - Door Panel - Rear - LH (Remove and Install).
  21. Raise LH rear window and close the LH doors.