Código de corrección 0.72 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

1. Use the vehicle touchscreen to depressurize the TAS system. See Air Suspension - Pressurize / Depressurize - Full System (Test/Adjust).
2. Remove the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
3. Release ANC air line from pressurized pack valve block
   Nota

   1x VOSS fitting, 12mm, 8 Nm, Do not release air line to reservoir, Rapid loss of pressure will result if wrong air line is released

   

4. Remove VOSS air fitting from ANC air line
   Nota

   1x VOSS fitting, Slide threaded section back, Remove collet, Then slide threaded section off of air line, Discard after removal

   

   

5. Release RES 2 air line from pressurized pack valve block
   Nota

   1x VOSS fitting, 10mm, 8 Nm

   

6. Remove VOSS air fitting from RES 2 air line
   Nota

   1x VOSS fitting, Slide threaded section back, Remove collet, Then slide threaded section off of air line, Discard after removal

   

   

7. Remove pressurized pack valve block
   Nota

   1x bolt, 10mm, 5 Nm, 1x connector, 2x datums

   

   

8. Install pressurized pack valve block
   Nota

   1x bolt, 10mm, 5 Nm, 1x connector, 2x datums

   

   

9. Install new VOSS air fitting onto RES 2 air line
   Nota

   1x VOSS fitting, 10mm, 8 Nm, Do not remove VOSS plastic plug until pressurized pack line is installed

   

   

10. Secure RES 2 air line onto pressurized pack valve block
    Nota

    1x line, Remove plastic cap from VOSS fittings, Press air lines onto fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test

    

    

11. Install new VOSS air fitting onto ANC air line
    Nota

    1x VOSS fitting, 12mm, 8 Nm, Do not remove VOSS plastic plug until pressurized pack line is installed

    

    

12. Secure ANC air line onto pressurized pack valve block
    Nota

    1x line, Remove plastic cap from VOSS fittings, Press air lines onto fitting until mark aligns with top of fitting, Verify line is properly secured by performing push and pull test

    

    

13. Install the bed floor assembly. See Truck Bed - Bed Floor Assembly (Remove and Install).
14. Pressurize the TAS system but do not exit Service Mode. See Air Suspension - Pressurize / Depressurize - Full System (Test/Adjust).
15. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Conexión y desconexión).
16. Click the Actions tab and search for "Pressurize".
17. Click Tesla Air Suspension Pressurize HV Pack, click Run, and allow routine to complete.
    Nota

    Select "X" at top right of window to close once complete, If reservoir air pressure is not ~16 bar then proceed to full system pressurize procedure, If pack is not able to maintain pressure post test then proceed to Pressurized Pack Not Holding Pressure inspection procedure, If pack is taking too long to pressurize then proceed to find leak
18. Disconnect Toolbox and remove the laptop from the vehicle. See Toolbox 3 (Conexión y desconexión).
19. Salga del Modo de servicio. Consulte Modo de servicio.
20. Suba la ventanilla delantera izquierda y cierre la puerta delantera izquierda.