Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

1. Eleve y apoye el vehículo. Consulte Elevación del vehículo - Elevador de 2 columnas.
2. Abra la puerta delantera izquierda y baje la ventanilla.
3. Coloque el vehículo en el Modo de servicio. Consulte Modo de servicio.
4. Desbloquee la puerta de enlace del vehículo. Consulte Puerta de enlace (Desbloquear).
5. Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
6. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
7. Remove the NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
8. Desconecte la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
9. Perform vehicle HV disablement procedure. See Vehicle HV Disablement Procedure (Test/Adjust).
10. Remove pyro fuse access cover
    Nota

    4x bolts, E-Torx 5 lobe, 10 Nm

    

11. Remove primary pyro fuse
    Nota

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

12. Remove secondary pyro fuse
    Nota

    2x bolts, 13mm, 5 Nm + 60 Degrees, Support pyro fuse while removing bolts

    

    

13. Lower vehicle until tires are touching the ground
    Nota

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
14. Disconnect ancillary bay MV connector
    Nota

    1x connector, Double locking, Release tab then pivot lever, Release second tab to disengage connector, Wait 1 second between locking tab release to discharge and prevent arcing

    

    

    

    

    

15. Remove bolt securing busbar HV connector lid
    Nota

    1x bolt, EP10, 9 Nm

    

16. Remove bolts securing HV connector to DC FC header
    Nota

    2x bolts, 10mm, 9 Nm

    

17. Release HV connector from DC FC header
    Nota

    1x connector, Use inflatable airbag if needed to suspend busbar assembly above ancillary assembly

    

18. Support HV Busbar assembly
    Nota

    1X Bungee, Suspend assembly to maintain clearance, wrap bungee around busbar assembly to achieve required cord length, Connect bungee to tie down hook on bed side

    

    

19. Remove fast charger header doubler
    Nota

    2x bolts, E10 5 Lobe Torx, 10 Nm

    

    

20. Remove mid voltage header bolts
    Nota

    2x bolts, EP10, 6 Nm

    

21. Release fasteners securing ancillary bay cover to HV battery
    Nota

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

22. Remove ancillary bay cover
    Nota

    Install vacuum cup to ancillary bay cover surface, Lift and maneuver cover around busbar and tonneau cage to remove

    

    

    

23. Install ancillary cover
    Nota

    Use suction cup and maneuver around busbar and tonneau cage

    

    

    

    

24. Secure ancillary cover fasteners to HV battery
    Nota

    22x bolts, E10 5-Lobe, 6 Nm, Use E10 5-Lobe socket without magnet, The fasteners are captive and will stay attached to the penthouse cover, Follow fastening order

    

    

    

25. Install mid voltage header bolts
    Nota

    2x bolts, EP10, 6 Nm

    

26. Install fast charger header doubler
    Nota

    2x bolts, E10 5 Lobe Torx, 10Nm

    

    

27. Clean HV connector contact surface of residual Penetrox
    Nota

    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

    

28. Clean busbar HV connector contact surface of residual Penetrox
    Nota

    Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

    

29. Apply Penetrox onto HV connector joints
    Nota

    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

    

30. Position busbar connector and lower onto HV header
    Nota

    Release bungee cord

    

31. Install bolts securing charge port busbar kit to HV Header
    Nota

    2x bolts, 10mm, 9 Nm

    

32. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    Nota

    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

33. Install bolt securing busbar HV connector lid
    Nota

    1x bolt, EP10, 9 Nm

    

34. Remove leather over gloves and HV insulating gloves
35. Connect ancillary bay MV connector
    Nota

    1x connector, double locking, Rotate lever into 2nd lock, Perform a pull test to ensure connector engaged correctly

    

    

    

    

    

36. Raise vehicle fully and lower lift onto locks
    Nota

    Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
37. Install secondary pyro fuse
    Nota

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

38. Install primary pyro fuse
    Nota

    2x bolts, 13mm, 5 Nm + 60 degrees, Support pyro fuse while installing bolts, Bolts may be reused

    

    

39. Perform Hioki resistance test at each HV joint from HV busbar lead to pyro fuse busbar
    Nota

    4x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

    

    

40. Install pyro fuse access cover with airlines attached
    Nota

    4x bolts, E-Torx 5 lobe, 10 Nm, Ensure seal is fully seated and undamaged, Secure 2 airline mounting clips to HV Battery, If HV pack is being shipped then pyro fuses must be removed

    

    

    

41. Remove leather over gloves and HV insulating gloves
42. Install the rear skid plate. See Skid Plate - Rear (Remove and Install).
43. Lower vehicle until tires are touching the ground
    Nota

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
44. Vuelva a conectar la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
45. Coloque el faldón trasero del vano del motor. Consulte Underhood Apron - Rear (Remove and Install).
46. Install the NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
47. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
48. Install the tonneau slats. See Slat System - Tonneau (Remove and Install).
49. Retire el vehículo del elevador. Consulte Elevación del vehículo - Elevador de 2 columnas.
50. Salga del Modo de servicio. Consulte Modo de servicio.
51. Suba la ventanilla delantera izquierda y cierre la puerta delantera izquierda.