Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

1. Open LH front door
   Nota

   Push LH B-pillar door trigger to release
2. Lower LH front window
3. Raise and support vehicle
   Nota

   Set air suspension to "Jack Mode"
4. Remove LH front wheel cover
   Nota

   6x tabs

   

   

   

5. Loosen LH front wheel nuts
   Nota

   6x nuts, 21mm, 205 Nm

   

6. Raise vehicle fully
   Nota

   Set to a comfortable working height, Lower to locks, Ensure locks engage on both sides to prevent tilting
7. Remove LH front wheel
   Nota

   6x nuts, 21mm, 205 Nm

   

8. Place wheel and tire on tire machine and secure
   Nota

   1x wheel clamp

   

   

9. Remove valve stem cap
   Nota

   1x cap

   

   

10. Remove valve stem core
    Nota

    Exercise caution as tire rapidly deflates, wear appropriate PPE

    

    

11. Rotate wheel and tire so that upper roller is ~100mm in front of the valve stem
    Nota

    Failure to properly position valve stem can result in TPMS damage

    

12. Break tire beads
    Nota

    Lubricate as required

    

    

    

13. Remove tire from wheel
    Nota

    Make sure to position the TPMS sensor ahead of the tire machine arm

    

    

    

    

    

    

14. Remove wheel from tire changer
    Nota

    1x clamp

    

15. Install valve stem
    Nota

    1x rubber valve stem, Insert from underneath, Pull up with installation tool until seated, Tire shown removed for clarity

    

    

16. Install wheel onto tire changer
    Nota

    1x clamp

    

17. Thoroughly lubricate both tire beads then position for installation
    Nota

    Make sure to position the TPMS sensor opposite the tire machine arm, Ensure wheel cover design side of tire is facing outwards

    

    

    

18. Install tire to wheel
    Nota

    Use caution to avoid damage to beads, Apply additional lubricant as required

    

    

    

    

    

19. Inflate the tire to seat beads
    Nota

    Do not exceed the pressure indicated on the tire sidewall, Wear PPE, Ensure inside and outside beads are seated

    

    

20. Install valve core stem
    Nota

    Hand tight only, Do not overtighten

    

    

21. Remove wheel and tire from tire changer
    Nota

    1x clamp

    

    

22. Install tire and wheel assembly onto balancer
    Nota

    1x 6-lug wheel flange, Position wheel onto spindle shaft then secure wheel using flange, If 6-lug wheel flange unavailable use 216mm Blue Hunter centering cone adapter

    

    

    

    

23. Remove wheel weights
    Nota

    1x tape weight, 1x hammer-on weight

    

    

24. Verify tire pressure is set
    Nota

    Set to specification, Refer to "Tire and Loading Information" label located on driver side B-pillar, Install valve stem cap

    

    

    

25. Input wheel dimensions into balancer machine
    Nota

    If machine does not require manual input then skip this step

    

26. Perform road force wheel balance
    Nota

    Follow machine instructions, Safety hood must be down to start balancing, Make sure load roller engages

    

27. Record road force wheel balance results
    Nota

    If road force is within limit then skip to install wheel weights, If road force is outside limit then proceed to force match

    

28. Perform tire and wheel force match
    Nota

    Measure run out then mark tire and rim for reference points, Use machine to determine points to match on tire and wheel

    

    

    

29. Remove tire and wheel assembly from balancer
    Nota

    1x 6-lug wheel flange, Remove flange then remove wheel from spindle shaft

    

30. Install tire and wheel assembly onto tire machine
    Nota

    1x wheel clamp, Position wheel onto wheel support then secure wheel using clamp

    

31. Remove valve stem cap
    Nota

    1x cap

    

    

32. Remove valve stem core
    Nota

    Exercise caution as tire rapidly deflates, Wear appropriate PPE

    

33. Break tire beads
    Nota

    Use lubrication around tire and wheel, Break top and bottom bead

    

    

34. Remove tire from wheel
    Nota

    Make sure to position TPMS sensor ahead of tire machine arm

    

    

    

35. Install tire onto wheel matching previously marked points from balancer
    Nota

    Rotate tire to align with previously marked reference points

    

    

    

36. Inflate tire to seat beads
    Nota

    Recommend assistance, Lift tire while inflating, Do not exceed pressure indicated on tire sidewall

    

37. Install valve stem core
    Nota

    Exercise caution as tire rapidly deflates, Wear appropriate PPE

    

38. Remove tire and wheel assembly from tire machine
    Nota

    1x wheel clamp, Remove clamp then remove wheel from wheel support

    

    

39. Install tire and wheel assembly onto balancer
    Nota

    1x 6-lug wheel flange, Position wheel onto spindle shaft then secure wheel using flange, If 6-lug wheel flange unavailable use 216mm Blue Hunter centering cone adapter

    

    

    

    

40. Verify tire pressure is set
    Nota

    Set to specification, Refer to "Tire and Loading Information" label located on driver side B-pillar, Install valve stem cap

    

    

    

41. Input wheel dimensions into balancer machine
    Nota

    If machine does not require manual input then skip this step

    

42. Perform road force wheel balance
    Nota

    Follow machine instructions, Safety hood must be down to start balancing, Make sure load roller engages

    

43. Install weights onto wheel
    Nota

    1x tape weight, 1x hammer on weight, Place weights on positions indicated by balancer

    

    

    

    

44. Perform check spin
    Nota

    Follow machine instructions, Safety hood must be down to start balancing, Make sure load roller engages

    

    

    

45. Remove tire and wheel assembly from balancer
    Nota

    1x 6-lug wheel flange, Remove flange then remove wheel from spindle shaft

    

46. Install LH front wheel
    Nota

    6x nuts, 21mm, 205 Nm

    

47. Lower vehicle until tires are touching the ground
    Nota

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
48. Torque LH front wheel nuts
    Nota

    6x nuts, 21mm, 205 Nm, Use star pattern

    

49. Install wheel cover

    

    

    

50. Remove vehicle from lift
    Nota

    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
51. Perform indirect TPMS calibration (Placeholder)
52. Road test vehicle - need to drive over 20 MPH to complete TPMS learn
    Nota

    Per current FRT (00040100) 0.3 hrs