2026-05-27

Tonneau Motor Assembly - LH (Standard) (Remove and Install)

Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
  • 2026-05-08: Released new procedure.
  1. Open tonneau cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press forward arrow on LH bed rail
  2. Open tailgate
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press button to release, Use manual release as necessary
  3. Remove fastener covers from bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    14x covers
  4. Remove bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance
  5. Remove LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Nota
    9x clips, 6x double-sided tape strips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip, Remove double-sided tape from applique and bed side, Remove any remaining adhesive with IPA wipes, Discard sail applique after removal, If superseded sail applique is present then discard and install latest revision
  6. Remove LH tonneau water management seal
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, Pull away from rail to release from groove
  7. Remove LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips, Start from rear, Lift tonneau seal as required. Pull from the bottom downwards.
  8. Remove LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle
  9. Remove LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 15mm, 46 Nm, 2x bolts, T45, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 3x connectorsRelease locking tabs, Disconnect bed outlet connectors from bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Release locking tabs, Slide lock to release.
  10. Remove LH tonneau motor
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, 2x bolts, 10mm, 11 Nm
  11. Install LH tonneau motor
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, 2x bolts, 10mm, 11 Nm
  12. Install LH lower bed side wall
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 15mm, 46 Nm, 2x bolts, 13mm, 36 Nm, 4x bolts, 10mm, 11 Nm, 2x nuts, 10mm, 7 Nm, 4x clips, 1x fastener cover, 1x connector, Secure locking tabs, Connect bed outlet connectors onto bed side wall and ground strap, 1x bolt, 10mm, 10 Nm, 2x connectors, Secure locking tabs, Slide lock to secure, Recommend assistance
  13. Install LH bed closeout panel
    Informational PurposesAn informational icon, calling your attention
    Nota
    6x clips, 1x tab, Secure LH tailgate cable once closeout installed
  14. Install LH upper bed side wall assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    8x clips, Replace any missing or damaged clips, Lift tonneau seal as required
  15. Install LH tonneau water management seal
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x clip, Push seal into rail groove
  16. Clean LH tonneau rail surface
    Informational PurposesAn informational icon, calling your attention
    Nota
    Remove any adhesive tape remaining, Use a cordless drill with eraser wheel attachment for ease adhesive residue removal, Wipe surface with IPA wipes, Allow IPA to dry for 1 minute
  17. Install LH sail applique
    Informational PurposesAn informational icon, calling your attention
    Nota
    "9x clips, 6x double-sided tape strips, 1x connector, 1x harness clip, 1x push nut, Install new LH sail applique, Do not remove forward section of double-sided tape backing until push nut is installed, Position applique, Partially lift applique to install push nut securing applique onto body, Connect and secure switch harness then secure rear of applique, Wet out urethane adhesive sections with roller, If superseded sail applique is present then discard and install latest revision
  18. Install bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    12x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance
  19. Install fastener covers onto bed floor assembly
    Informational PurposesAn informational icon, calling your attention
    Nota
    14x covers
  20. Close tonneau cover
  21. Close tailgate