Código de corrección 12150300401 12150300402 1.14 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

1. Open tailgate
   Nota

   Press button to release, Use manual release as necessary

   

2. Remove fastener covers from bed floor assembly
   Nota

   14x covers

   

   

   

   

   

3. Remove bed floor assembly
   Nota

   10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Lift front edge with trim tool then remove panel, Recommend assistance

   

   

   

   

4. Remove LH sail applique
   Nota

   15x clips, 1x connector, 1x harness clip, Lift rear edge first to remove connector and harness clip

   

   

   

   

5. Remove LH upper bed side wall assembly
   Nota

   13x clips, Start from rear, Pull from the bottom downwards

   

   

6. Remove LH bed closeout panel
   Nota

   6x clips, 1x tab, Release LH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off to allow removal of bed closeout panel from vehicle

   

   

   

   

7. Remove LH lower bed side wall
   Nota

   2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

   

   

   

   

   

   

   

8. Remove RH sail applique
   Nota

   15x clips

   

   

   

9. Remove RH upper bed side wall assembly
   13x clips, Pull downwards

   

   

10. Remove RH bed closeout panel
    Nota

    6x clips, 1x tab, Release RH tailgate cable by disengaging lock spring from bolt and sliding cable eyelet off in order to remove bed closeout panel from vehicle

    

    

    

    

11. Remove RH bed side wall
    Nota

    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

    

    

    

    

    

    

    

    

    

12. Remove Damper Bed Reinforcement Assembly

    

13. Install Damper Bed Reinforcement Assembly

    

14. Install RH bed side wall
    Nota

    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

    

    

    

    

    

    

    

    

    

15. Install RH bed closeout panel
    Nota

    6x clips, 1x tab, Release RH tailgate cable to install bed closeout panel from vehicle

    

    

    

16. Install RH upper bed side wall assembly
    Nota

    13x clips, Replace any missing or damaged clips

    

    

17. Install RH sail applique
    Nota

    13x clips, Replace any damaged clips

    

    

18. Install LH lower bed side wall
    Nota

    2x bolt, 15mm, 25 Nm, 4x bolts, 10mm, 11 Nm, 4x nuts, 10mm, 10 Nm, 1x connector, 4x L track fastener covers

    

    

    

    

    

    

    

    

19. Install LH bed closeout panel
    Nota

    6x clips, 1x tab, Secure LH tailgate cable once closeout installed

    

    

    

20. Install LH upper bed side wall assembly
    Nota

    13x clips, Replace any missing or damaged clips, Lift tonneau seal as required

    

    

21. Install LH sail applique
    Nota

    15x clips, 1x connector, 1x harness clip, Replace any broken clips

    

    

22. Install bed floor assembly
    Nota

    10x short bolts, 15mm, 56 Nm, 2x long bolts, 15mm, 46Nm, Recommend assistance

    

    

    

    

    

23. Install fastener covers onto bed floor assembly
    Nota

    14x covers

    

    

    

    

24. Close tailgate