2024-12-10

Mud Flaps (Retrofit)

Código de corrección 12207006 0.24 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.

Retroadaptar

  1. Open the LH front door and lower the LH front window.
  2. Turn the steering wheel fully to the left to provide access to the working areas.
  3. Remove the clips (x2) that partially attach the LH front wheel arch liner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Herramienta de retirada de clips con palanca
    Figura 1. LH shown; RH similar
  4. Position the LH front mud flap on the vehicle, and then install the clips (x2) that attach the mud flap to the LH front wheel arch liner.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Install the clips starting from right to left.
    Figura 2. LH shown; RH similar
    Figura 3. LH shown; RH similar
  5. Install the bolts (x2) that attach the LH front mud flap to the LH rocker panel.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Nota
    Align the bolts with the rocker panel holes.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Extensión de 2 pulg.
    • Vaso de 10 mm de cuello largo
    • Destornillador de impacto/carraca sin cable
    • Llave dinamométrica con medición de ángulos
    Figura 4. LH shown; RH similar
  6. Remove the clips (x3) that partially attach the RH rear wheel arch liner to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Herramienta de retirada de clips con palanca
    Figura 5. RH shown; LH similar
  7. Remove the bolt that partially attaches the RH rear diffuser to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Extensión de 2 pulg.
    • Destornillador de impacto/carraca sin cable
    • Vaso Torx T30
    Figura 6. RH shown; LH similar
  8. Move the RH rear wheel arch liner away from the working area as required, and then install the U-nuts (x3) onto the RH rear fascia.
    Figura 7. RH shown; LH similar
  9. Move the RH rear wheel arch liner back to original position.
    Figura 8. RH shown; LH similar
  10. Position the RH rear mud flap on the vehicle, and then install the bolts (x3) that attach the mud flap to the RH rear wheel arch liner.
    2.2 Nm (1.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm de cuello largo
    • Destornillador de impacto/carraca sin cable
    • Llave dinamométrica con medición de ángulos
    Figura 9. RH shown; LH similar
    Figura 10. RH shown; LH similar
  11. Install the bolt that attaches the RH rear mud flap to the RH rear diffuser.
    2.2 Nm (1.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm de cuello largo
    • Destornillador de impacto/carraca sin cable
    • Llave dinamométrica con medición de ángulos
    Figura 11. RH shown; LH similar
  12. Turn the steering wheel fully to the right to provide access to the working areas.
  13. Repeat step 3 through step 5 for the RH front mud flap.
  14. Repeat step 6 through step 11 for the LH rear mud flap.
  15. Raise the LH front window and close the LH front door.