2026-08-14

Busbar - Charge Port (Long Range) (Remove and Install)

Código de corrección NA NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT asociado reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver prácticas de trabajo seguras.

Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
Aviso
Los componentes electrónicos del Cybertruck están alimentados por una arquitectura de media tensión de 48 V diseñada para mejorar la eficiencia. El mantenimiento de los componentes de media tensión requiere un conocimiento y cuidado adicionales para evitar daños personales o en el vehículo. Lea y comprenda las precauciones relacionadas con la media tensión en Precauciones eléctricas y asegúrese de realizar todos los cursos de formación necesarios, según corresponda.
Aviso
Solo los técnicos que hayan recibido formación en sistemas de alta tensión y hayan completado todos los cursos de certificación necesarios (si procede) pueden realizar este procedimiento. Siempre que se manipule un cable, barra colectora o conexión de alta tensión, deben llevarse equipos de protección individual (EPI) y guantes aislantes para alta tensión con una clasificación nominal mínima de 0 (1000 V). En la nota técnica TN-15-92-003 sobre los puntos de peligro de alta tensión, encontrará más información sobre guantes y seguridad.
  • 2025-06-21: Released new procedure.
  1. Abra el portón trasero.
  2. Abra la puerta delantera izquierda y baje la ventanilla.
  3. Abra el maletero delantero eléctrico.
  4. Using MCU open charge port door
  5. Extraiga el faldón trasero del vano del motor. Consulte Underhood Apron - Rear (Remove and Install).
  6. Desconecte la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
  7. Verify operation of multimeter
    Nota
    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing MV battery, Touch lightly and do not damage terminals
  8. Remove all items from pockets and ensure not wearing metal items
  9. Inspect HV insulating gloves
    Nota
    Check gloves for damage prior to use, Refer to service document TN-15-92-003
  10. Put on HV insulating gloves and leather over gloves
  11. Verify there is no high voltage present at the charge port
    Nota
    Measure B+ to B-, and B+ to Ground and B - to Ground, Place Alligator clip onto body panel
  12. Remove leather over gloves and HV insulating gloves
  13. Remove both LH rear fore and aft fender flares
    Nota
    12 clips, 9x tabs
  14. Remove clips securing LH rear wheel liner to aft fender flare carrier
    Nota
    2x clips
  15. Remove LH rear aft fender flare carrier
    Nota
    2x bolts, 10mm, 7 Nm, 2x datum
  16. Remove clips securing LH rear wheel liner to fore fender flare carrier
    Nota
    5x clips
  17. Remove LH rear fore fender flare carrier
    Nota
    6x bolts, 10mm, 7 Nm, 1x connector, Disconnect BLE module then remove carrier, Release locking tab
  18. Remove the LH lower bed side wall. See Wall Assembly - Bed Side - Lower - LH (Long Range) (Remove and Install).
  19. Remove bolt securing busbar HV connector lid
    Nota
    1x bolt, EP10, 9 Nm
  20. Remove bolts securing HV connector to DC FC header
    Nota
    2x bolts, 10mm, 9 Nm
  21. Release HV connector from DC FC header
    Nota
    1x connector, Use inflatable airbag to suspend busbar assembly above ancillary assembly
  22. Remove connector from chargeport assembly
    Nota
    1x connectors, Remove white locking tab, Depress tab to release connection from the charge port, Continue to pull off connector, The charge port connection is intended to disengage safety cap when released, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
  23. Remove chargeport door and LV connector
    Nota
    2x connector, 1x clip
  24. Remove bolt securing ground cable to busbar assembly
    Nota
    1x bolt, 10mm, 6.5 Nm
  25. Release chargeport from outer sail
    Nota
    1x bolt, 10mm, 6.5 Nm
  26. Remove bolts securing chargeport assembly onto body
    Nota
    2x bolts, 10mm, 6 Nm, Use only hand tools, Risk of galling if power tools used on stainless fasteners
  27. Remove chargeport and busbar from vehicle
  28. Clean HV connector contact surface of residual Penetrox
    Nota
    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector
  29. Apply Penetrox onto HV connector joints
    Nota
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered
  30. Position chargeport busbar assembly onto vehicle
  31. Install bolts securing charge port busbar kit to HV Header
    Nota
    2x bolts, 10mm, 9 Nm
  32. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    Nota
    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step
  33. Install bolts securing chargeport assembly onto body
    Nota
    2x bolts, 10mm, 6 Nm, Use only hand tools, Risk of galling if power tools are used on stainless fasteners
  34. Install chargeport to outer sail
    Nota
    1x bolt, 10mm, 6.5 Nm
  35. Install busbar ground bolt
    Nota
    1x bolt, 10mm, 6.5 Nm
  36. Install chargeport door and LV connector
    Nota
    2x connectors, 1x clip
  37. Engage charge port connector
    Nota
    1x connector, Fully engage connection and white locking tab, The connector is intended to lock the safety cap in place
  38. Install the LH lower bed side wall. See Wall Assembly - Bed Side - Lower - LH (Long Range) (Remove and Install).
  39. Install LH rear fore fender flare carrier
    Nota
    6x bolts, 10mm, 7 Nm, 1x connector, Connect BLE then install carrier, Engage locking tab
  40. Install clips securing LH rear wheel liner to fore fender flare carrier
    Nota
    5x clips
  41. Install clips securing LH rear wheel liner to aft fender flare carrier
    Nota
    2x clips
  42. Install both LH rear fore and aft fender flares
    Nota
    12 clips, 9x tabs
  43. Vuelva a conectar la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
  44. Coloque el faldón trasero del vano del motor. Consulte Underhood Apron - Rear (Remove and Install).
  45. Suba la ventanilla delantera izquierda y cierre la puerta delantera izquierda.
  46. Cierre el portón trasero.