2026-07-27

HV Connector - Busbar - Charge Port (Standard) (Remove and Install)

Código de corrección NEW NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Los componentes electrónicos del Cybertruck están alimentados por una arquitectura de media tensión de 48 V diseñada para mejorar la eficiencia. El mantenimiento de los componentes de media tensión requiere un conocimiento y cuidado adicionales para evitar daños personales o en el vehículo. Lea y comprenda las precauciones relacionadas con la media tensión en Precauciones eléctricas y asegúrese de realizar todos los cursos de formación necesarios, según corresponda.
Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Solo los técnicos que hayan recibido formación en sistemas de alta tensión y hayan completado todos los cursos de certificación necesarios (si procede) pueden realizar este procedimiento. Siempre que se manipule un cable, barra colectora o conexión de alta tensión, deben llevarse equipos de protección individual (EPI) y guantes aislantes para alta tensión con una clasificación nominal mínima de 0 (1000 V). En la nota técnica TN-15-92-003 sobre los puntos de peligro de alta tensión, encontrará más información sobre guantes y seguridad.
  • 2026-05-08: Released new procedure.
  1. Abra la puerta delantera izquierda y baje la ventanilla.
  2. Remove the tonneau slats. See Slat System - Tonneau (Remove and Install).
  3. Eleve y apoye el vehículo. Consulte Elevación del vehículo - Elevador de 2 columnas.
  4. Abra la cubierta de la plataforma de carga.
  5. Abra el portón trasero.
  6. Remove the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
  7. Remove the NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
  8. Desconecte la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
  9. Secure RDU header connector to ancillary
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins
  10. Lower vehicle until tires are touching the ground
    Informational PurposesAn informational icon, calling your attention
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  11. Remove bolt securing busbar HV connector lid
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, EP10, 9 Nm
  12. Remove bolts securing HV connector to DC FC header
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 9 Nm
  13. Release HV connector from DC FC header
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Use inflatable airbag if needed to suspend busbar assembly above ancillary assembly
  14. Raise CP busbar connector
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x inflatable bags, Install bags, Do not open tonneau to prevent damage
  15. Remove screws securing HV connector to CP busbars
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x screws, T20, 1.5 Nm, Position mirror as needed
  16. Remove HV connector from CP busbars
    Informational PurposesAn informational icon, calling your attention
    Nota
    Gently pry between orange clips and primary heat sink, Pull evenly
  17. Position HV connector onto CP busbars
    Informational PurposesAn informational icon, calling your attention
    Nota
    Push evenly, Make sure orange clips are flush with primary heat sink
  18. Install screws securing HV connector to CP busbars
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x screws, T20, 1.5 Nm, Position mirror as needed
  19. Clean HV connector contact surface of residual Penetrox
    Informational PurposesAn informational icon, calling your attention
    Nota
    Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector
  20. Apply Penetrox onto HV connector joints
    Informational PurposesAn informational icon, calling your attention
    Nota
    Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered
  21. Clean busbar HV connector contact surface of residual Penetrox
    Informational PurposesAn informational icon, calling your attention
    Nota
    Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar
  22. Lower CP busbar connector
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x inflatable bags, Remove bags, Do not open tonneau to prevent damage
  23. Position busbar connector and lower onto HV header
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release bungee cord
  24. Install bolts securing charge port busbar kit to HV Header
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 10mm, 9 Nm
  25. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x HV joints, When using Hioki tester, verify the meter has been properly adjusted and set prior to usageThe acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), stop work and escalate the Toolbox session.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step
  26. Install bolt securing busbar HV connector lid
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, EP10, 9 Nm
  27. Vuelva a conectar la alimentación de media tensión. Consulte Mid-Voltage Power (Disconnect and Connect) (Modify).
  28. Install the NVH barrier. See Tonneau NVH Barrier Assembly (Remove and Install).
  29. Install the bed floor assembly. See Bed Floor Assembly (Long Range) (Remove and Install).
  30. Coloque el faldón trasero del vano del motor. Consulte Underhood Apron - Rear (Remove and Install).
  31. Cierre la cubierta de la plataforma de carga.
  32. Cierre el portón trasero.
  33. Install the rear skid plate. See Skid Plate - Rear (Remove and Install).
  34. Coloque el faldón trasero del vano del motor. Consulte Underhood Apron - Rear (Remove and Install).
  35. Install the tonneau slats. See Slat System - Tonneau (Remove and Install).