2025-02-09

Front Drive Unit Assembly - Gearbox Fluid (Fill to Spill)

Código de corrección NA NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.
  1. Eleve y apoye el vehículo. Consulte Elevación del vehículo - Elevador de 2 columnas.
  2. Abra la puerta delantera izquierda y baje la ventanilla delantera izquierda.
  3. Coloque el vehículo en el Modo de servicio. Consulte Modo de servicio.
  4. Remove the front aero shield. See Undertray - Front Aeroshield (Remove and Install).
  5. Position an oil drain container underneath the oil pump.
  6. Release the clips (x2) that attach the RH side of the acoustic cover to the lower portion of the acoustic cover.
  7. Release the clips (x2) that attach the RH side of the acoustic cover to the front drive unit.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Route the cover between the subframe and halfshaft.
  8. Remove oil fill plug from FDU
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x plug, 8mm Allen, 15 Nm, Verify the O-ring is not damaged, Replace O-ring as needed
  9. Inspect plug O-rings
    Informational PurposesAn informational icon, calling your attention
    Nota
    Inspect O-ring on fill plug, if damaged replace affected plug
  10. Set up fill kit with KAF1
    Informational PurposesAn informational icon, calling your attention
    Nota
    Fill oil generously to container as it will prevent underfill and additional air being injectedOnly use KAF1 fluid, Do not interchange or mix oil types
  11. Position oil pump hose into FDU fill hole
  12. Pump fluid into FDU
    Informational PurposesAn informational icon, calling your attention
    Nota
    Fill to spill, Only use KAF1 fluid, Do not interchange or mix oil types, Note amount needed, If more than 300mL is needed then escalate to Service Engineering
  13. Remove oil pump hose from FDU fill hole
    Informational PurposesAn informational icon, calling your attention
    Nota
    Turn valve to off and remove from fill hole
  14. Install oil fill plug onto FDU
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x plug, 8mm Allen, 15 Nm, Verify the O-ring is not damaged, Replace O-ring as needed
  15. Spray area with brake cleaner and wipe any residual fluid
  16. Secure the clips (x2) that attach the RH side of the acoustic cover to the front drive unit.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Route cover between subframe and axle.
  17. Secure the clips (x2) that attach the RH side of the acoustic cover to the lower portion of the acoustic cover.
  18. Install the front aero shield. See Undertray - Front Aeroshield (Remove and Install).
  19. Lower the vehicle until the tires are touching the ground.
  20. Salga del Modo de servicio. Consulte Modo de servicio.
  21. Retire el vehículo del elevador. Consulte Elevación del vehículo - Elevador de 2 columnas.
  22. Suba la ventanilla delantera izquierda y cierre la puerta delantera izquierda.