20/12/2023 17:14:22

Fascia Assembly - Rear - Lower (Remove and Replace)

Code de correction 10012902

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Warning IconA warning icon, calling your attention to a possibly risky situation
ATTENTION
Pour l’Europe seulement : Seuls les techniciens qui ont été formés pour travailler avec d’isocyanate et qui ont complété toutes les formations de certification requises sont autorisés à effectuer des procédures utilisant de l'uréthane et d'autres produits contenant des isocyanates. Vous devez porter un équipement de protection personnel (ÉPP) approprié lorsque vous travaillez avec des produits qui contiennent des diisocyanates.

Removal

  1. Open LH front door.
  2. Lower LH front window.
  3. Open liftgate.
  4. Raise and support vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set air suspension to "Jack Mode" Via Controls > Service > ''Jack Mode''.
  5. Raise vehicle fully and lower onto locks.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
  6. Remove bolts securing mid aero shield to rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x bolts, 10mm, 4 Nm, 2x bolt, T30, 4.5 Nm.
  7. Lower vehicle to comfortable working height.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Ensure the vehicle is stable by rocking the vehicle on the lift immediately after the tires have left the ground, Always lower the lift arms onto the locks after raising the vehicle.
  8. Remove LH liftgate stop from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bump stop.
  9. Remove RH liftgate stop from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bump stop.
  10. Remove LH liftgate trough trim .
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 4x double sided tape strip .
  11. Remove RH liftgate trough trim .
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 4x double sided tape strip .
  12. Remove bolt securing LH top of fascia to bracket.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolts, 10mm, 4 Nm.
  13. Remove bolt securing RH top of fascia to bracket.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolts, 10mm, 4 Nm.
  14. Remove clip securing LH rear fender garnish and arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clip.
  15. Remove clip securing RH rear fender garnish and arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clip.
  16. Partially release LH rear fender garnish from rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 7 tabs.
  17. Partially release RH rear fender garnish from rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 7 tabs.
  18. Remove screw securing LH rear fascia to quarter panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  19. Remove screw securing RH rear fascia to quarter panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  20. Apply masking tape to protect LH rear quarter panel.
  21. Apply masking tape to protect RH rear quarter panel.
  22. Remove rear fascia from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    24x tabs, Recommended assistance, Take care not to damaged connectors and harness while pulling fascia away from vehicle, Connectors removal next step.
  23. Disconnect rear fascia harness connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Located on LH rear side, Recommend assistance, Place fascia on padded surface.
  24. Remove both rear reflex lamps from rear fascia applique.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips2x 10mm metal clip .
  25. Remove screws securing diffuser to fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x screws, 10mm, 3 Nm.
  26. Remove diffuser from rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips, 13x clips, Recommend assistance.
  27. Remove screws securing lower fascia to rear fascia .
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x screws, 10mm, 3 Nm.
  28. Remove Lower Fascia from Rear Fascia .
    Informational PurposesAn informational icon, calling your attention
    Remarque
    21x clips, Recommend assistance.

Installation

  1. Install Lower Fascia to Rear Fascia .
    Informational PurposesAn informational icon, calling your attention
    Remarque
    21x clips, Recommend assistance.
  2. Install screws securing lower fascia to rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x screws, 10mm, 3 Nm.
  3. Install diffuser to rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips, 13x clips, Recommend assistance.
  4. Install screws securing diffuser to fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x screws, 10mm, 3 Nm.
  5. Install rear reflex lamps into new rear fascia applique.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips2x 10mm metal clip.
  6. Reconnect rear fascia harness connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Located on LH rear side, Recommend assistance, Position fascia for install.
  7. Install rear fascia onto vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    24x tabs, Recommended assistance, Align mounting 2 top studs.
  8. Remove masking tape from LH rear quarter panel.
  9. Remove masking tape from RH rear quarter panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    .
  10. Install screw securing LH rear fascia to quarter panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  11. Install screw securing RH rear fascia to quarter panel.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  12. Install LH rear fender garnish onto rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 7 tabs.
  13. Install RH rear fender garnish onto rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips, 7 tabs.
  14. Install clip securing LH rear fender garnish and arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clip.
  15. Install clip securing RH rear fender garnish and arch liner.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x push clip.
  16. Install bolt securing LH top of fascia to bracket.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolts, 10mm, 4 Nm.
  17. Install bolt securing RH top of fascia to bracket.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolts, 10mm, 4 Nm.
  18. Clean LH liftgate body trough trim surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use IPA wipes to clean body surface where trough trim is fasten with double sided strip, Allow 1 minute for dry time.
  19. Clean RH liftgate body trough trim surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use IPA wipes to clean body surface where trough trim is fasten with double sided strip, Allow 1 minute for dry time.
  20. Clean LH liftgate trough trim surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use IPA wipes to clean trough trim where double sided tape is attached to, Allow 1 minute for dry time, Apply 3M tape primer to tape surface .
  21. Clean RH liftgate trough trim surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Use IPA wipes to clean trough trim where double sided tape is attached to, Allow 1 minute for dry time, Apply 3M tape primer to tape surface .
  22. Install double sided tape onto LH trough trim.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x double sided tape strip.
  23. Install double sided tape onto RH trough trim.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x double sided tape strip.
  24. Install LH liftgate trough trim into place.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 4x double sided tape strip, Remove tape backing before installation, Partially lift the main seal for better access.
  25. Install RH liftgate trough trim into place.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip, 4x double sided tape strip, Remove tape backing before installation, Partially lift the main seal for better access.
  26. Install LH liftgate stop from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bump stop.
  27. Install RH liftgate stop from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bump stop.
  28. Close liftgate.
  29. Raise vehicle fully and lower onto locks.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Ensure the vehicle is stable by rocking the vehicle on the lift immediately after the tires have left the ground, Always lower the lift arms onto the locks after raising the vehicle.
  30. Install bolts securing mid aero shield to rear fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x bolts, 10mm, 4 Nm, 2x bolt, T30, 4.5 Nm.
  31. Lower vehicle until tires are touching the ground.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  32. Remove vehicle from lift.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lower rack arms fully and move them from under vehicle, Remove air suspension from "Jack Mode" Controls => Service => Jack Mode.
  33. Raise LH front window.
  34. Close LH front door.