20/12/2023 17:14:18

Seal - Door - Rear - Upper - LH (Remove and Replace)

Code de correction 11706002

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open LH rear door and lower the window
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure window is fully lowered
  2. Open hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using MCU touchscreen > Controls > Frunk Trunk
  3. Remove underhood aprons
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons
  4. Remove frunk carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  5. Remove underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
  6. Remove HEPA filter
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lift up from bottom and pull out
  7. Move LH 2nd row seat fully forward using easy entry mode
  8. Remove LH falcon door lower garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x V-clips, Replace any damaged or missing V-clips, Take care not to damage door trim panel during removal
  9. Remove LH upper falcon door trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    17x clips, 1x connector may be present on early production vehicles
  10. Remove LH upper outer falcon door rear trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x bolts, T25, 2.5 Nm, 4.0 Nm, 1x harness clip, Fastener count may vary
  11. Remove LH upper outer falcon door front trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x bolts, T25, 2.5 Nm, 4.0 Nm, 1x harness clip, Fastener count may vary
  12. Remove LH upper outer falcon door middle trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, T25, 3.0 Nm, 4.0 Nm, Fastener count may vary
  13. Remove LH upper gap hider trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  14. Lower LH falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    May need to assist the door to close
  15. Remove LH falcon door upper glass
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x nuts, 10mm, 6 Nm, Recommend assistance
  16. Set LH Falcon door fully open
  17. Support the rear door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    May need assist to open
  18. Power down vehicle using MCU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via Controls > Safety & Security > ''Power off''
  19. Disconnect 12V negative terminal and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components
  20. Disconnect LH rear secondary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Black
  21. Disconnect LH rear primary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, White
  22. Disconnect LH front secondary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Black
  23. Disconnect LH front primary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, White
  24. Remove the rear primary strut from upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x C-clip, 1x harness clip
  25. Remove the front primary strut from upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x C-clip, 1x harness clip
  26. Remove the front bump stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 8 Nm, 1x bolt, T30, 5 Nm, Mark or remember the position of the bump stop to aid the installation process
  27. Remove the rear bump stop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 8 Nm, 1x bolt, T30, 5 Nm, Mark or remember the position of the bump stop to aid the installation process
  28. Remove the upper falcon door NVH seal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make a cut in the seal and remove from the perimeter of the door, Try to remove as much double sided tape with the seal as possible
  29. Remove any double side tape or adhesive from upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Roll the residual adhesive manually for best results
  30. Position NVH seal for installation
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Slide seal over the lower falcon door assembly to the cavity between upper and lower falcon door
  31. Use IPA to clean NVH seal area of the upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Allow 1 minute for IPA to dry
  32. Place falcon door NVH seal around perimeter of upper door frame and tape in position
  33. Install new upper falcon door NVH seal to upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x Double-sided tape sections, Seat inner corners first and finish on an edge, Press firmly to wet-out seal, Remove blue tape as needed
  34. Install LH front upper falcon door bumpstop assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 8Nm, 1x screw, T30, 5Nm
  35. Install LH rear upper falcon door bumpstop assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 8Nm, 1x screw, T30, 5Nm
  36. Install the rear primary strut to upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x C-clip, 1x harness clip, Door may need to be lifted to align strut, Recommend assistance
  37. Install the front primary strut to upper falcon door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x C-clip, 1x harness clip, Door may need to be lifted to align strut, Recommend assistance
  38. Connect LH front primary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, White
  39. Connect LH front secondary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Black
  40. Connect LH rear primary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, White
  41. Connect LH rear secondary strut
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Black
  42. Remove door support stand
  43. Connect first responder loop and then 12V negative terminal
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 1x nut, 10mm, 5 Nm
  44. Calibrate falcon doors using MCU
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Required after 12V and FRL disconnect
  45. Install LH falcon door upper glass
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x nuts, 10mm, 6 Nm, Recommend assistance
  46. Install LH upper gap hider trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips
  47. Install LH upper outer falcon door middle trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    7x bolts, T25, 3.0 Nm, 4.0 Nm, Fastener count may vary
  48. Install LH upper outer falcon door front trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x bolts, T25, 2.5 Nm, 4.0 Nm, 1x harness clip, Fastener count may vary
  49. Install LH upper outer falcon door rear trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x bolts, T25, 2.5 Nm, 4.0 Nm, 1x harness clip, Fastener count may vary
  50. Install LH upper falcon door trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    17x clips, Align strut cover first, 1x connector may be present on early production vehicles
  51. Install LH falcon door lower garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x V-clips, 1x guide tab
  52. Reposition the LH seat to original position
  53. Install HEPA filter housing
  54. Install underhood storage unit
    Informational PurposesAn informational icon, calling your attention
    Remarque
    10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
  55. Install frunk carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors
  56. Install under hood aprons
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons
  57. Close hood
  58. Close LH rear door and window