2025-06-27
Brake Pads and Rotors - Front - Set
Code de correction 33010905
- 2025-05-14: Updated brake burnishing step.
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
- Open LH front door.
-
Raise and support vehicle.
RemarqueSet air suspension to Jack Mode, Via Controls > Service > Jack Mode, Raise lift until arms contact the lift points
- Remove RH front lug nut covers (x5).
-
Loosen RH front lug nuts.
Remarque5x nuts, 21mm, 175 Nm
- Remove LH front lug nut covers (x5).
-
Loosen LH front lug nuts.
Remarque5x nuts, 21mm, 175 Nm
-
Raise vehicle partially and lower onto locks.
RemarqueSet vehicle to comfortable working height, make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
-
Remove RH front wheel.
Remarque5x nuts, 21mm, 175 Nm
-
Remove LH front wheel.
Remarque5x nuts, 21mm, 175 Nm
- Turn front wheels fully right.
-
Remove pins and anti-rattle spring from LH front caliper.
RemarqueHold spring while removing pin, Remove upper pin first, Air hammer may be required to remove stuck pins
-
Press inner and outer brake pads out to push caliper pistons back into LH front caliper.
RemarqueWrap a shop rag around the caliper to protect the finish if using pliers, Air hammer may be required to free stuck pads
-
Remove brake pads from LH front caliper.
RemarquePuller or air hammer may be required to free stuck pads
-
Use hand brush and brake cleaner to clean LH front caliper pad slides and pistons.
RemarqueUse nylon brush on painted calipers, Allow brake cleaner to dry, replace caliper if excessive corrosion is found.
-
Apply Silaramic lubricant to both LH front inner and outer pads on caliper pad slides.
Remarquekeep lubricant off pad friction material, only on backing plate.
-
Use hand brush and brake cleaner to clean LH front caliper pins and anti-rattle spring.
RemarqueReplace pins and spring if there is excessive corrosion or damage to components.
-
Install LH front inner and outer brake pads.
RemarqueDo not allow any lubricant to get onto friction surfaces, Clean friction surfaces with brake cleaner if necessary.
-
Install anti-rattle spring and caliper pins for LH front caliper.
RemarqueInstall lower pin first, make sure both pins are fully seated.
- Center front wheels.
-
Remove bolts securing LH rear brake caliper to knuckle.
Remarque2x bolts, 18mm, 120 Nm, Support the caliper with “S” hook.
-
Remove LH front brake caliper from LH front knuckle assembly and hang.
RemarqueSupport the caliper with “S” hook
-
Remove bolt securing brake rotor to hub and bearing assembly.
Remarque1x bolt, T45, 17 Nm, Discard patch bolt after removal.
- Remove brake rotor from hub and bearing assembly.
-
Install LH front brake rotor onto hub and bearing assembly.
RemarqueAlign bolt hole in rotor to hub for next step.
-
Install bolt securing brake rotor to hub and bearing assembly.
Remarque1x bolt, T45, 17 Nm, Install new patch bolt
- Remove LH front brake caliper from brake caliper S-hook.
-
Position and install LH front brake caliper onto LH front knuckle assembly.
Remarque2x bolts, 18mm, 120 Nm
-
Install LH front wheel.
Remarque5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
- Turn front wheels fully to the left.
-
Remove pins and anti-rattle spring from RH front caliper.
RemarqueHold spring while removing pin, Remove upper pin first, Air hammer may be required to remove stuck pins
-
Press inner and outer brake pads out to push caliper pistons back into RH front caliper.
RemarqueWrap a shop rag around the caliper to protect the finish if using pliers, Air hammer may be required to free stuck pads
-
Remove brake pads from RH front caliper.
RemarquePuller or air hammer may be required to free stuck pads
-
Use hand brush and brake cleaner to clean RH front caliper pad slides and pistons.
RemarqueUse nylon brush on painted calipers, Allow brake cleaner to dry, Replace caliper if excessive corrosion is found
-
Apply Silaramic lubricant to both RH front inner and outer pads on caliper pad slides.
Remarquekeep lubricant off pad friction material, only on backing plate
-
Use hand brush and brake cleaner to clean RH front caliper pins and anti-rattle spring.
RemarqueReplace pins and spring if there is excessive corrosion or damage to components
-
Install RH front inner and outer brake pads.
RemarqueDo not allow any lubricant to get onto friction surfaces, Clean friction surfaces with brake cleaner if necessary
-
Install anti-rattle spring and caliper pins for RH front caliper.
RemarqueInstall lower pin first, Make sure both pins are fully seated
- Center front wheels.
-
Remove the bolts securing the RH front brake caliper to the knuckle.
Remarque2x bolts, 18mm, 120 Nm
- Remove the RH front brake caliper from the knuckle and hang.
-
Remove bolt securing brake rotor to hub and bearing assembly.
Remarque1x bolt, T45, 17 Nm, Discard patch bolt after removal
- Remove brake rotor from hub and bearing assembly.
-
Install LH front brake rotor onto hub and bearing assembly.
RemarqueAlign bolt hole in rotor to hub for next step
-
Install bolt securing brake rotor to hub and bearing assembly.
Remarque1x bolt, T45, 17 Nm, Install new patch bolt
- Remove the RH front brake caliper from the S-hook.
-
Position and install RH front brake caliper onto RH front knuckle assembly.
Remarque2x bolts, 18mm, 120 Nm
-
Install RH front wheel.
Remarque5x nuts, 21mm, 175 Nm, Thread nuts on by hand
-
Lower vehicle until tires are touching ground.
RemarqueRaise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Torque LH front wheel.
Remarque5x nuts, 21mm, 175 Nm
- Install LH front lug nut covers (x5).
-
Torque RH front wheel.
Remarque5x nuts, 21mm, 175 Nm
- Install RH front lug nut covers (x5).
-
Remove vehicle from lift.
RemarqueLower rack arms fully and move them from under vehicle, Remove air suspension from "Jack Mode", Via Controls > Service > Jack Mode
-
Pump the brake pedal a few times to ensure the pedal feels normal.
RemarqueCheck for a short, firm travel when the brakes are applied, If the brake pedal is soft, bleed the complete system
- Close LH front door.
-
Rodez les freins. Voir Plaquettes de frein - frein de stationnement - brunissage.
RemarqueLorsque vous conduisez le véhicule, vérifiez que la pédale de frein réagit et fonctionne comme prévu.RemarqueAjoutez le code de correction pour le rodage des plaquettes de frein 33013000 en tant qu’activité distincte lors de la visite d’entretien.