2026-07-02

Basic Vehicle Inspection (Inspection)

Code de correction 00030700 FRT 1.08 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire indiqués ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lorsque vous effectuez la procédure ci-dessous. REMARQUE : Voir Précautions ergonomiques pour consulter les pratiques de travail sécuritaires et saines.

Avertissement

Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension.

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

Remarque
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check all windows from the master switch

Remarque
Document any abnormal operation/noises
Function check LH rear door (exterior)

Remarque
Inspect and note functionality for the door handle operation, and full range of motion of the door, From outside look for interference with brightwork and door to body, Function test closing button on door, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

Remarque
Inspect and note functionality for the door handle operation, and fullrange of motion of the door, Function test closing button on door, From outside, look for interference with brightwork and door to body. Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

Remarque
Inspect and note functionality for the door handle operation, and full range of motion of the door. From outside, look for interference with brightwork and door to body. Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check the exterior lights

Remarque
Recommend assistance, inspect and note functionality of: Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH), and license plate lights
Activate windshield washers and verify washer nozzle spray pattern
Function check horn
Check all emergency release cables and switches

Remarque
Rear door releases, Liftgate release, Rear door releases accessible behind speaker grille
Open hood

Remarque
Via center display > Controls > Front Trunk
Remove underhood aprons

Remarque
4x aprons, LH and RH aprons have 1x clip each, First remove rear apron, Then remove LH and RH aprons, Last remove front apron
Remove frunk carpet

Remarque
2x connectors, Release the carpet from underneath the seal
Remove frunk assembly

Remarque
10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm
Remove HEPA filter housing

Remarque
Lift up from bottom and pull out, *Note: There may or may not be a filter in housing based on vehicle configuration
Perform inspection of under hood area

Remarque
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect brake fluid level
Inspect coolant level and top off as necessary

Remarque
Ensure coolant is filled using G-48 coolant
Raise vehicle fully and lower lift onto locks

Remarque
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove front aero shield

Remarque
6x bolts, 10mm, 3 Nm, 14x clips
Remove rear aero shield

Remarque
20x bolts, 10mm, 4 Nm, 2x push clips
Check tire pressures

Remarque
4x tires, Set to specification if necessary
Measure and record LH front tread depth

Remarque
Record at least 3 measurements: Inner, Middle, Outer
Measure and record LH front brake pad thickness
Inspect LH front brake rotor condition

Remarque
Check for excessive rust or wear
Measure and record RH front tread depth

Remarque
Record at least 3 measurements: Inner, Middle, Outer
Measure and record RH front brake pad thickness
Inspect RH front brake rotor condition

Remarque
Check for excessive rust or wear
Measure and record LH rear tread depth

Remarque
Record at least 3 measurements: Inner, Middle, Outer
Measure and record LH rear brake pad thickness
Inspect LH rear brake rotor condition

Remarque
Check for excessive rust or wear
Measure and record RH rear tread depth

Remarque
Record at least 3 measurements: Inner, Middle, Outer
Measure and record RH rear brake pad thickness
Inspect RH rear brake rotor condition

Remarque
Check for excessive rust or wear
Inspect brake hose condition

Remarque
Look for evidence of brake hose(s) rubbing on surrounding components, Inspect hose connections for evidence of leaks, Verify hoses are routed properly and secured to retaining brackets
Perform inspection of vehicle underside components front and rear

Remarque
Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect underside of vehicle for coolant or brake fluid leaks
Perform inspection of steering components

Remarque
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of front suspension components

Remarque
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

Remarque
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Inspect HV battery for damage

Remarque
Check for dents, fluid leaks, or other signs of instability, If damage found then reach out to Service Engineering
Install rear aero shield

Remarque
20x bolts, 10mm, 4 Nm, 2x push clips. Start bolts with cordless, torque with 1/4 torque wrench
Install front aero shield

Remarque
6x bolts, 10mm, 3 Nm, 14x clips
Lower vehicle fully

Remarque
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Install HEPA filter housing

Remarque
Align opening on back of housing to HEPA filter outlet duct opening, *Note: There may or may not be a filter in housing based on vehicle configuration
Install frunk assembly

Remarque
10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm, Hand start all bolts first then tighten with tools
Install frunk carpet

Remarque
2x connectors, Make sure that the carpet is attached beneath the seal.
Install under hood aprons

Remarque
4x aprons, First install front apron, Then install LH and RH aprons, Last install rear apron
Close hood
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

Remarque
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

Remarque
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction