Code de correction 13026502

1. Open LH front door
2. Using MCU, open all doors, liftgate and hood

   

3. Move LH front seat forward
4. Move RH front seat forward
5. Open hood
   Remarque

   Using MCU touchscreen > Controls > Frunk Trunk
6. Remove underhood aprons
   Remarque

   4x aprons

   

7. Remove frunk carpet
   Remarque

   2x connector

   

8. Remove underhood storage unit
   Remarque

   10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm

   

   

   

9. Remove HEPA filter
   Remarque

   Lift up from bottom and pull out

   

10. Remove 2nd row floor mat

    

11. Remove LH welcome plate
    Remarque

    8x clips

    

12. Remove LH rear door sill
    Remarque

    1x patch bolt, T25, 2.5 Nm, 2x clips, Discard after removal

    

13. Move 60 seat fully forward using easy entry

    

    

14. Tape the LH lower C-pillar area around the 2nd row seat side trim area

    

15. Apply tape to LH racetrack to avoid damage

    

16. Remove front screw securing LH lower C-pillar
    Remarque

    1x patch screw, T25, 2.5 Nm, Discard after removal

    

17. Fold down LH 3rd row seat
    Remarque

    Press button located on LH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position

    

18. Fold down RH 3rd row seat
    Remarque

    Press button located on RH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position

    

19. Remove LH trunk sill side trim
    Remarque

    4x clips

    

20. Remove screw securing LH C-pillar mid trim
    Remarque

    1x screw, T20, 2 Nm

    

21. Release clips securing LH C-pillar mid trim and remove
    Remarque

    9x clips

    

22. Remove screws securing C-pillar lower panel to LH parcel shelf support
    Remarque

    2x screws, T20, 2 Nm

    

23. Release clips securing rear edge of LH C-pillar lower panel to rear trunk side carpet panel and pull top edge of C-pillar lower panel out
    Remarque

    2x clips, 1x magnet

    

24. Release clips securing LH C-pillar lower panel along front edge and remove panel
    Remarque

    9x clips, 1x magnet

    

25. Remove RH trunk sill side trim
    Remarque

    4x clips

    

26. Remove screw securing RH C-pillar mid trim
    Remarque

    1x screw, T20, 2 Nm

    

27. Release clips securing RH C-pillar mid trim and remove
    Remarque

    9x clips

    

28. Remove fasteners securing C-pillar lower panel to RH parcel shelf support
    Remarque

    2x screws, T20, 2 Nm

    

29. Remove RH welcome plate
    Remarque

    8x clips

    

30. Remove front screw securing RH lower C-pillar
    Remarque

    1x screw, T25, 2.5 Nm, Discard after removal

    

31. Remove RH rear door sill trim
    Remarque

    1x patch bolt, T25, 2.5 Nm, 2x clips, Discard bolt after removal

    

32. Move 40 seat fully forward using easy entry

    

    

33. Tape the RH lower C-pillar area around the 2nd row seat side trim area

    

34. Apply tape to the RH racetrack to avoid damage

    

35. Release clips securing RH C-pillar lower panel along front edge and remove panel
    Remarque

    9x clips, 1x magnet

    

36. Move 40 seat back and out of easy entry position

    

37. Move 60 seat back and out of easy entry position

    

38. Tape rear center console cup holder trim to prevent from damage

    

39. Remove 2nd row floor panel 2
    Remarque

    6x clips, Replace any broken clips, Lift the front of panel toward the rear of the vehicle, then pull the floor panel out

    

    

40. Move 60 seat fully forward using easy entry

    

    

41. Move 40 seat fully forward using easy entry

    

    

42. Remove 2nd row floor panel 3
    Remarque

    Lift front of panel up to release clips, While lifting up, need to release the rear sliding plates from the seat and slide them all the way back, Once free, lift rear of panel and slide out from behind seats, Use caution since floor panel can damage HVAC ducts

    

    

43. Move 60 seat fully backwards
    Remarque

    Using easy entry unlatch seat and move it fully backwards, Create space to inspect under seat, Latch seatback to lock into position

    

    

    

44. Power down vehicle using MCU
    Remarque

    Via Controls > Safety & Security > ''Power off''

    

45. Disconnect 12V negative terminal and First Responder Loop
    Remarque

    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components

    

    

46. Remove LH bench seat floor support

    

47. Remove center bench seat floor support

    

48. Disconnect 60 seat harness
    Remarque

    2x connectors, Release bracket for better access

    

    

49. Release harness from LH floor support bracket
    Remarque

    2x clips

    

50. Remove LH outer sliding closeout panel
    Remarque

    1x clip, Need to peel sticker back to release clip

    

    

51. Remove LH inner sliding closeout panel
    Remarque

    1x clip, Need to peel sticker back to release clip

    

    

52. Remove fasteners securing the 60 bench
    Remarque

    12x bolts, 11mm, 45 Nm

    

    

53. Fold down 60 seat

    

54. Remove 60 seat assembly from vehicle
    Remarque

    Recommend assistance

    

55. Unfold the 60 seat assembly

    

56. Release rear toe kick from 60 seat assembly
    Remarque

    6x J-hooks, Release lower outer two to expose inner 4 clips

    

    

57. Remove center seat belt buckle from seat
    Remarque

    1x patch bolt, T50, 45 Nm, Discard after removal, 1x connector, 1x edge clip

    

    

58. Remove 60 seat assembly release handle
    Remarque

    Pry at pivot point to release

    

59. Remove LH outer recliner cover
    Remarque

    1x bolt, 10mm, 6 Nm, 1x push clip, 4x clips

    

    

    

60. Remove LH outer seat belt from the 60 seat assembly
    Remarque

    1x patch bolt, T50, 45 Nm, Discard after removal

    

61. Release upholstery from under side of 60 seat assembly
    Remarque

    11x J-hooks

    

    

    

    

    

    

62. Disconnect seat cushion connectors
    Remarque

    2x gray connectors, 2x black connectors, Black connectors must be released from seat frame

    

    

63. Remove lower seat cushion from LH 60 seat assembly
    Remarque

    Use caution feeding J-hooks and connectors through seat frame

    

64. Remove RH fasteners securing the inner riser cover
    Remarque

    2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm

    

65. Remove RH fasteners securing the outer riser cover
    Remarque

    1x screw, T20, 4 Nm

    

66. Remove RH riser cover from seat
    Remarque

    2x clips

    

67. Remove LH fasteners securing the outer riser cover
    Remarque

    2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm

    

68. Remove LH fasteners securing the inner riser cover
    Remarque

    1x screw, T20, 4 Nm

    

69. Remove RH riser cover from seat
    Remarque

    2x clips

    

70. Remove screw securing splitter box to 60 seat assembly
    Remarque

    1x screw, T20, 1.5 Nm

    

71. Remove screw securing splitter box spring to 60 seat assembly
    Remarque

    2x screws, T20, 1.5 Nm

    

72. Remove the front cushion support
    Remarque

    5x bolts, 10mm, 6 Nm

    

73. Release cable from the LH track
    Remarque

    1x cable, cable is secured in bracket at to points

    

74. Release cable from the RH track
    Remarque

    1x cable, cable is secured in bracket at to points

    

75. Release both cables from cable clips
    Remarque

    3x cable clips, Leave the clip in the seat frame, release the cable from the clip only

    

76. Remove the bolt securing actuator assembly to seat frame
    Remarque

    1x bolt, 10mm, 6 Nm

    

77. Remove actuator assembly from seat frame
    Remarque

    1x cable, turn 30 degrees to right and push back to remove from seat frame

    

78. Remove actuator assembly from seat assembly
    Remarque

    1x cable, Remove actuator cable from actuator assembly

    

    

79. Position and install actuator assembly to actuator
    Remarque

    1x cable, Do not remove the black pin before the actuator assembly cable is attached to the actuator

    

    

80. Install actuator assembly onto seat frame
    Remarque

    Attach actuator assembly onto back tab then move forward and turn 30 degrees to latch on the second tab

    

81. Install the bolt securing actuator assembly to seat frame
    Remarque

    1x bolt, 10mm, 6 Nm

    

82. Connect the RH side cable to the track
    Remarque

    2x cable bracket

    

83. Connect the LH side cable to the track
    Remarque

    2x cable bracket

    

84. Install both cables to cable clips
    Remarque

    3x cable clips

    

85. Install bolts securing the front cushion support
    Remarque

    6x bolts, 10mm, 6 Nm

    

86. Install screw securing splitter box to 60 seat assembly
    Remarque

    1x screw, T20, 1.5 Nm

    

87. Install screw securing splitter box spring to 60 seat assembly
    Remarque

    2x screw, T20, 1.5 Nm

    

88. Install RH riser cover onto the seat
    Remarque

    Make sure to secure the clips

    

89. Install the LH outer fasteners
    Remarque

    2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm

    

90. Install the LH inner fasteners
    Remarque

    3x screw, T20, 4 Nm

    

91. Install RH riser cover onto the seat
    Remarque

    Make sure to secure the clips

    

92. Install the RH inner fasteners
    Remarque

    1x screw, T20, 4 Nm

    

93. Install the RH outer fasteners
    Remarque

    2x screw bottom, T20, 2 Nm, 1x screw top, T20, 4 Nm

    

94. Install cushion onto the seat
    Remarque

    Use caution feeding J-hooks and connectors through seat frame

    

95. Connect seat cushion connectors
    Remarque

    2x gray connectors, 2x black connectors, Secure black connectors to seat frame

    

    

96. Secure upholstery to under side of 60 seat assembly
    Remarque

    11x J-hooks, Position cushion onto seat frame and then fold seat back down for better access, Fold seat back up once complete

    

    

    

    

    

    

97. Install LH outer seat belt to the 60 seat assembly
    Remarque

    1x patch bolt, T50, 45 Nm, Install new patch bolt

    

98. Install LH outer recliner cover
    Remarque

    1x bolt, 10mm, 6 Nm, 1x push clip, 4x clips

    

    

    

99. Install 60 seat assembly release handle
    Remarque

    1x spring clip

    

100. Install LH center seat belt buckle onto seat
     Remarque

     1x patch bolt, T50, 45 Nm, Install new patch bolt, 1x connector, 1x edge clip

     

     

101. Secure toe kick to 60 seat assembly
     Remarque

     6x J-hooks, Secure inner 4 clips, then lower outer 2

     

     

102. Fold 60 seat back down

     

103. Install 60 seat assembly into vehicle
     Remarque

     Recommend assistance, Make sure guide pins are aligned properly

     

104. Unfold the 60 seat assembly

     

105. Install forward most 60 seat track bolts hand tight
     Remarque

     2x bolts, 11mm, 45 Nm

     

106. Secure 60 seat harness to LH floor support bracket
     Remarque

     2x clips

     

107. Connect 60 seat assembly harness
     Remarque

     2x connectors, Secure connector housing to bracket

     

     

108. Connect first responder loop and then 12V negative terminal
     Remarque

     1x connector, 1x nut, 10mm, 5 Nm

     

     

109. Move 60 seat fully forward using easy entry

     

     

110. Install rear center 60 seat track bolts
     Remarque

     2x bolts, 11mm, 45 Nm

     

111. Install remaining rear 60 seat track bolts
     Remarque

     4x bolts, 11mm, 45 Nm

     

112. Move 60 seat back and out of easy entry position

     

113. Torque forward most 60 seat track bolts
     Remarque

     2x bolts, 11mm, 45 Nm

     

114. Install remaining front 60 seat track bolts
     Remarque

     4x bolts, 11mm, 45 Nm

     

115. Install center bench seat floor support

     

116. Install LH bench seat floor support

     

117. Install LH inner sliding closeout panel
     Remarque

     1x clip, Need to lay sticker back down to cover the fastener

     

     

118. Install LH outer sliding closeout panel
     Remarque

     1x clip, Need to lay sticker back down to cover the fastener

     

     

119. Move 40 seat fully forward using easy entry

     

     

120. Move 60 seat fully forward using easy entry

     

     

121. Install 2nd row floor panel 3
     Remarque

     2x clips, Use caution near HVAC ducts

     

122. Move 60 seat back and out of easy entry position
     Remarque

     Moving seat fully rearward will secure sliding plates to seat

     

123. Move 40 seat back and out of easy entry position
     Remarque

     Moving seat fully rearward will secure sliding plates to seat

     

124. Install 2nd row floor panel 2
     Remarque

     6x clips, Replace clips if damaged, Install rear of panel into position and then secure clips

     

125. Remove tape from rear center console trim

     

126. Move 40 seat fully forward using easy entry

     

     

127. Move 60 seat fully forward using easy entry

     

     

128. Install RH C-pillar lower panel and secure clips along front edge
     Remarque

     9x clips, 1x magnet

     

129. Install screw securing front of RH lower C-pillar
     Remarque

     1x patch screw, T25, 2.5 Nm, Install new screw

     

130. Install RH rear door sill trim
     Remarque

     1x patch bolt, T25, 2.5 Nm, 2x clips, Install new patch bolt

     

131. Install RH welcome plate
     Remarque

     8x clips

     

132. Remove masking tape from the RH lower C-pillar

     

133. Secure clips holding rear edge of RH C-pillar lower panel to rear trunk side carpet panel
     Remarque

     3x clips, 1x magnet

     

134. Install fasteners securing C-pillar lower panel to RH parcel shelf support
     Remarque

     2x screws, T20, 2 Nm

     

135. Install RH C-pillar mid trim
     Remarque

     9x clips, Install front section first, then work around to rear

     

136. Install screw securing RH C-pillar mid trim
     Remarque

     1x screw, T20, 2 Nm

     

137. Install RH trunk sill side trim
     Remarque

     4x clips

     

138. Install LH lower C-pillar and secure clips along front edge
     Remarque

     9x clips, 1x magnet

     

139. Install bolt securing front of LH lower C-pillar
     Remarque

     1x bolt, T25, 2.5 Nm, Install new patched bolt

     

140. Install LH rear door sill trim
     Remarque

     1x patch bolt, T25, 2.5 Nm, 2x clips, Install new patch bolt

     

141. Install LH welcome plate
     Remarque

     8x clips

     

142. Remove masking tape from the LH lower C-pillar

     

143. Secure clips at rear edge of LH C-pillar lower panel
     Remarque

     2x clips, 1x magnet

     

144. Install fasteners securing C-pillar lower panel to LH parcel shelf support
     Remarque

     2x screws, T20, 2 Nm

     

145. Install LH C-pillar mid trim and secure clips
     Remarque

     9x clips, Install front section first, then work around to rear

     

146. Install screw securing LH C-pillar mid trim
     Remarque

     1x screw, T20, 2 Nm

     

147. Install LH trunk sill side trim
     Remarque

     4x clips

     

148. Fold LH 3rd row seat up
     Remarque

     Press button located on LH 3rd row seat back assembly near headrest, lift seat back into an upright position

     

149. Fold RH 3rd row seat up
     Remarque

     Press button located on LH 3rd row seat back assembly near headrest, lift seat back into an upright position

     

150. Close liftgate

     

151. Move 60 seat back and out of easy entry position

     

152. Remove tape from LH racetrack trim

     

153. Move 40 seat back and out of easy entry position
     Remarque

     Moving seat fully rearward will secure sliding plates to seat

     

154. Remove tape from RH racetrack trim

     

155. Install 2nd row floor mat

     

156. Install HEPA filter housing

     

157. Install underhood storage unit
     Remarque

     10x bolts, 10mm, 4 Nm, 10x bolts, 10mm, 7 Nm

     

     

     

158. Install frunk carpet
     Remarque

     2x connector

     

159. Install under hood aprons
     Remarque

     4x aprons

     

160. Close hood
161. Move RH front seat to original position
162. Close RH front door
163. Move LH front seat to original position
164. Calibrate falcon doors using MCU
     Remarque

     Required after 12V and FRL disconnect

     

165. Close LH front door