08/04/2024 13:07:31

Harness - Fascia - Front (Remove and Replace)

Code de correction 17101002

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Remove

  1. Open LH front door
  2. Raise and support vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set air suspension to Jack Mode, Via Controls > Service > Jack Mode, Raise lift until arms contact the lift points
  3. Open hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via center display > Controls > Front Trunk
  4. Remove underhood aprons
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons, LH and RH aprons have 1x clip each
  5. Raise vehicle partially and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  6. Remove clips and pull back on LH front wheelhouse liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips
  7. Remove clip securing LH wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  8. Remove bolts securing LH wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm
  9. Release clips securing the front half of the LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, Be cautious of parking sensor
  10. Disconnect LH fender garnish parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Pull red tab to disengage lock
  11. Release clips securing rear half of LH front garnish and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  12. Remove screw securing LH fascia to fender
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm
  13. Remove clips and pull back on RH front wheelhouse liner
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips
  14. Remove clip securing RH front wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  15. Remove bolts securing RH front wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm
  16. Release clips securing the front half of the RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, Be cautious of park sensor
  17. Disconnect LH parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  18. Release clips securing rear half of RH front garnish and remove from vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  19. Remove screw securing RH fascia to fender
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm
  20. Raise vehicle fully and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  21. Remove clips securing fascia to lower front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x push clips
  22. Remove fasteners securing fascia to lower front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 3 Nm
  23. Lower vehicle fully
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  24. Remove bolts securing fascia to upper grill
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm
  25. Remove front fascia assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 1x connector, Place fascia onto padded surface, Recommend assistance
  26. Place fascia on padded surface
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure the front of the fascia is facing down
  27. Remove the bolt securing the LH wheelhouse duct to the LH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 2.5 Nm
  28. Lift the LH wheelhouse duct to gain access to the LH fascia lamp assembly connector and disconnect the LH fascia lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  29. Disconnect the LH outer parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  30. Disconnect the LH inner parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  31. Disconnect the RH inner parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  32. Disconnect the RH outer parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  33. Remove the fastener securing the RH wheelhouse duct to the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 2.5 Nm
  34. Lift the RH wheelhouse duct to gain access to the RH fascia lamp assembly connector and disconnect the RH fascia lamp
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  35. Remove the white harness retaining clip from the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  36. Remove the harness retaining fir tree clip from the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x fir tree clip
  37. Remove fascia harness from the 6 anchor locations etched on the surface of the fascia
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x anchors
  38. Remove any residual adhesive from the 6 anchor points on the surface of the fascia and clean with IPA
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x anchors

Install

  1. Place the harness into the front fascia for installation
  2. Install the white retaining clip securing front fascia harness on the LH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  3. Install the fir tree clip securing front fascia harness on the LH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x fir tree clip
  4. Install the retaining clip securing front fascia harness at the upper section of the LH wheelhouse duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  5. Install the retaining clip securing front fascia harness at the upper section of the RH wheelhouse duct
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  6. Install fascia harness to the 6 anchor locations etched on the surface
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x anchors, Peel the backing off the double sided tape and apply pressure to the tape once in position, Ensure the tape is wet out properly
  7. Install the fir tree clip securing front fascia harness on the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x fir tree clip
  8. Install the white retaining clip securing front fascia harness on the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  9. Install the fastener securing the LH wheelhouse duct to the LH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, 10mm, 2.5 Nm
  10. Connect the RH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  11. Connect the RH outer parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  12. Connect the RH inner parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  13. Connect the LH inner parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  14. Connect the LH outer parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  15. Connect the LH fascia lamp assembly
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  16. Install front fascia assembly to vehicle
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Recommend assistance
  17. Install bolts securing fascia to upper grill
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm
  18. Raise vehicle fully and lower onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Ensure the vehicle is stable by rocking the vehicle on the lift immediately after the tires have left the ground, Always lower the lift arms onto the locks after raising the vehicle
  19. Install clips securing fascia to lower front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x push clips, Indicated in red
  20. Install fasteners securing fascia to lower front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 3 Nm
  21. Lower vehicle partially and set lift onto locks
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  22. Install screw securing RH fascia to fender
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm
  23. Install rear half of the RH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  24. Connect RH front fender garnish parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  25. Install the front half of the RH front garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, Be cautious of parking sensor, Be sure to align fender ducts
  26. Secure bolts for RH front wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm
  27. Secure clip for RH front wheel fairing
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  28. Fully secure RH front wheelhouse liner to fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips
  29. Install screw securing LH fascia to fender
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm
  30. Install rear half of LH front fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x clips
  31. Connect RH front fender garnish parking sensor
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  32. Install front half of LH front garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, Be cautious of parking sensor, Be sure to align fender ducts
  33. Install bolts securing LH front wheel fairing to front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm
  34. Install clip securing LH front wheel fairing to front aero shield
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x push clip
  35. Fully secure LH front wheelhouse liner to fender garnish
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x push clips
  36. Lower vehicle fully
  37. Install under hood aprons
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons
  38. Close hood
  39. Remove vehicle from lift
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Lower rack arms fully and move them from under vehicle, Remove air suspension from "Jack Mode", Via Controls > Service > Jack Mode
  40. Close LH front door