20/12/2023 17:14:32

Harness - Main Front (Remove & Replace)

Code de correction 17100702

Dépose

  1. Open the LH front door.
  2. Raise and support the vehicle. See Soulever le véhicule - pont élévateur à 2 poteaux.
  3. Install a steering wheel holder.
  4. Remove the underhood storage unit. See Unité de rangement sous le capot (retirez et remplacez).
  5. Remove the HEPA filter housing and the HEPA filter duct. See Conduit – filtre HEPA (retrait et remplacement)
  6. Start the A/C refrigerant recovery procedure. See Récupération et recharge du fluide frigorigène de climatisation (retrait et remplacement).
  7. Remove the wiper arms. See Bras d’essuie-glace - gauche (retrait et remplacement).
  8. Remove the cowl screen from windshield. See Panneau – auvent (Retirer et remplacer)
  9. Allow 15 minutes for the A/C refrigerant recovery procedure to finish.
  10. Disconnect the blue and red A/C machine hoses from the vehicle.
  11. Power down the vehicle using the MCU.
  12. Disconnect 12V power. See Disconnect 12V Power.
  13. Remove the front aero shield. See Panneau - écran aérodynamique - avant (retirez et remplacez).
  14. Remove the LH and RH wheelhouse liner. See Doublure d’aile - avant - gauche (retirez et remplacez).
  15. Remove the front fascia assembly. See Ensemble de carénage - avant (retrait et installation).
  16. Remove the HV battery assembly. See Batterie HT (AWD) (retirez et installez).
  17. Disconnect the 12V logic connector from the RH side of the DC/DC converter.
  18. Disconnect the low voltage connector from battery coolant pump 1.
  19. Disconnect the low voltage connector from battery coolant pump 2.
  20. Release the fir tree clip that mounts the battery pump 1 pigtail to the subframe.
  21. Disconnect the power steering logic connectors (x2).
  22. Disconnect the ESP ECU connector.
  23. Disconnect the LH front pressure sensor.
  24. Disconnect the power and ground connectors from the power steering ECU.
  25. Lower the vehicle to a comfortable working height.
  26. Disconnect the 12V connector from the battery chiller EXV valve.
  27. Release the fir tree clip that mounts the EXV chiller harness to the frame.
  28. Disconnect the connectors (3x) from the LH acceleration sensor, the washer fluid pump and the washer fluid level sensor.
  29. Disconnect the connectors (2x) from the LH horn.
  30. Disconnect the LH front Air suspension module, and then loosen the harness edge clip.
  31. Disconnect the LH headlamp connector.
  32. Pull the LH front harness upward.
  33. Remove the 12V Auxiliary battery. Refer to Batterie – auxiliaire – 12 V (retrait et remplacement).
  34. Remove wiper motor assembly. See Module d’essuie-glace (conduite à gauche) (retirez et remplacez)or Module d’essuie-glace (conduite à droite) (retirez et remplacez)
  35. Remove the push clips (x2) that attach the cowl screen support, and then remove the cowl screen support.
  36. Release the push clips (x2) that attach the fuse box harness to the wiper mount bracket and the crossmember.

  37. Remove the bolts (x2) that attach the wiper mount bracket to the crossmember (torque 20 Nm).
  38. Remove the nuts (x2) that attach the wiper mount bracket to the studs on the bulkhead (torque 20 Nm).
  39. Release the clips (x2) that attach the LH front air suspension line to the air suspension reservoir brackets.
  40. Release the nuts (x4) that attach the air suspension reservoir (torque 6 Nm) to the brackets, and then carefully maneuver the air suspension reservoir away from the bulkhead.
  41. Remove the cap from the coolant reservoir, and then siphon the coolant from the reservoir into a container.
  42. Disconnect the coolant fluid level sensor electrical connector.
  43. Remove the bolts (x4) that attach the coolant reservoir to the front crossmember (torque 6 Nm).
  44. Release the 12V harness clip from the coolant reservoir.
  45. Clamp both coolant hoses from the reservoir, and then move the reservoir off to the side.
  46. Disconnect the LH front wheel speed sensor.
  47. Remove the bolts (x2) that connect the ground cables to the LH front strut tower (torque 12 Nm) and then remove the ground cables.
  48. Remove the fuse box. See Boîte de fusibles – sous le capot (retrait et remplacement)
  49. Loosen the nyloc nut that connects the ground cable to the intelligent battery sensor (torque 2,5 Nm), and then remove the ground cable.
  50. Disconnect the brake fluid level sensor.
  51. Disconnect the connectors (x2) from the electromechanical brake booster.
  52. Release the fir tree clips (x5) that attach the harness to the front upper post and lower upper post.
  53. Disconnect the AC low pressure sensor connector and the AC compressor logic connector, and then loosen the bolt (torque 1.8 Nm) that attaches the ground connector to the AC compressor.
  54. Disconnect the center acceleration sensor.
  55. Disconnect the Logic connector from the FDU harness.
  56. Disconnect the connectors (x4) from the RH front air suspension module and the Air suspension compressor.
  57. Disconnect the RH front acceleration sensor.
  58. Release the fir tree clip and the connector clip that attaches the harness to the RH front wheel arch area.
  59. Disconnect the connectors (x4) from the RH front horn and the front center harness.
  60. Loosen the front antenna, and then release the cable from the wiring clips (x2)
  61. Release the fir tree clips (x2) and remove the zip tie, and then release the harness from the RH front wheel arch area.
  62. Disconnect the RH front headlamp.
  63. Pull the RH front harness upward.
  64. Release the fir tree clip, and then disconnect the RH front wheel speed sensor
  65. Loosen the bolts (x3) that connect the front ground cables to the RH front strut tower (torque 12 Nm), and then remove the ground cables.
  66. Disconnect the Chiller valve block.
  67. Remove the edge clips (x2) that attach the active shutter harness to the active shutter assembly.
  68. Disconnect the active shutter and move the harness aside.
  69. Release the retaining clips (x2), and then remove the active shutter assembly.
  70. Clamp the hoses (x2) on the LH and RH sides of the radiator.
  71. Put a coolant drain container under the LH front corner of the vehicle.
  72. Loosen the hose clamp of the radiator outlet hose on the LH side of the radiator, and then remove the radiator outlet hose.
  73. Loosen the hose clamp of the front drive unit outlet hose on the RH side of the radiator, and then remove the front drive unit outlet hose.
  74. Remove fir tree clip that attaches the cooling fan harness to the cooling fan shroud.
  75. Disconnect the cooling fan.
  76. Loosen the bolts (x2) that attach the cooling fan shroud to the support beam (torque 12 Nm).
  77. Remove the upper nuts (x2, torque 10 Nm) and the lower nuts (x2, torque 20 Nm) that attach the high and low pressure pipes to the condenser
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Install new O-rings
  78. Lift the rear of the cooling fan module and slide the assembly away from the front end module to remove the cooling fan module from the vehicle.
  79. Remove the coolant drain container from under the front of the vehicle.
  80. Remove the fir tree clip that attaches the cowl drain hose to the 4-way valve.
  81. Remove the connectors (x2) from the 3-way valve and the 4-way valve.
  82. Remove the clips (x2) that attach the harness to the 3-way valve and 4-way valve.
  83. Remove the E-Fuse module. See Module de fusibles électroniques (retrait et remplacement).
  84. Release the 12V harness clips (x4) from the front junction box and the air suspension ECU enclosure.
  85. Disconnect the logic connector from the front junction box.
  86. Open the air suspension ECU enclosure (torque 1.2 Nm).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T30, 1.2 Nm
  87. Loosen the nuts (x3, torque 4.5 Nm), and then pull the air suspension enclosure aside.
  88. Loosen the connectors from the air suspension ECU (x10) and then release the harness from the ECU enclosure.
  89. Disconnect the battery heater connector from the battery heater bracket, and then remove the fir tree clip that attaches the battery heater connector to the battery bracket.
  90. Disconnect the powertrain coolant pump 1.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The powertrain coolant pump 1 is located on the RH side of the vehicle.
  91. Disconnect the powertrain coolant pump 2.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The powertrain coolant pump 2 is located on the LH side of the vehicle.
  92. Remove the screw that secures the front of the LH rocker panel molding (torque 3 Nm).
  93. Open the covers (x5) on the bottom of the rocker panel molding to expose the hidden push clips.
  94. Remove the push clips (x6) that attach the rocker panel molding to the bottom of the rocker panel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Replace any broken clips.
  95. Release the clips (x14) that secure the rocker panel molding to the rocker panel carrier.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Replace any broken clips.
  96. Remove the rocker panel molding from the vehicle.
  97. Carefully lift and remove the LH LF antenna, and then move the harness up the fender.
  98. Repeat steps 92 to 97 to remove the RH rocker panel and RH LF antenna.
  99. Remove the RH floor mat.
  100. Remove RH side footwell cover. See Ensemble - Recouvrement - Espace de jambes - Côté passager (retrait et remplacement)
  101. Remove the RH rear door sill trim. See Garniture - panneau de seuil - arrière - gauche (retrait et remplacement)
  102. Remove the RH front door sill trim. See Garniture - panneau de seuil - avant - gauche (retrait et remplacement)
  103. Remove the RH instrument panel side cover. See Ensemble - couvercle latéral du tableau de bord - gauche (retrait et remplacement).
  104. Remove the RH front lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez)
  105. Release the fir tree clip that attaches the RH front rear carpet to the floor, and then fold the carpet out of the way.
  106. Loosen the fan clips (x2) and fir tree clips (x2) that attach the foam support to the floor, and then remove the foam floor support.
  107. Disconnect the connectors (x5) of the main front body harness from the RH side of the cabin fusebox bracket.
  108. Loosen the nut (torque 3 Nm) that attaches the main front body harness to the RH side of the cabin fusebox bracket.
  109. Remove the LH front floor mat.
  110. Remove the LH center console closeout extension. See Rallonge de fermeture - console centrale - gauche (retirez et remplacez)
  111. Loosen the nut (torque 3Nm) and disconnect the connector of the main front body harness from the LH side of the cabin fusebox bracket.
  112. Push the firewall grommet out and slide the main front body harness out of the interior of the car.
  113. Pull out the main front body harness from behind the strut tower, and then remove the harness from the vehicle.

Installation

Installation procedure is the reverse of removal, except for the following:
  1. Reconnect and install all components. Perform the following steps before installation of the HEPA filter and housing, the underhood storage unit and underhood aprons.
  2. Fill the coolant reservoir to the "NOM" line with G-48 coolant.
  3. Connect a laptop with Toolbox 3 to the vehicle.
  4. Unlock the gateway. See Déverrouillage de passerelle.
  5. In Toolbox 3, click the Actions tab, type "Coolant air purge" into the search field, click PROC_THC_X_COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Coolant Air Purge, click Run, and allow the routine to complete.
  6. Disconnect the laptop from the vehicle.
  7. Top off the coolant reservoir to the "NOM"line.
  8. Install coolant reservoir cap.
  9. Calibrate the falcon doors using the MCU.