03/06/2024 17:05:15

Link - Aft - Lower - LH (Remove and Replace)

Code de correction 31013602

  • 12-03-2024 : Ajout d'un avertissement pour rappeler aux techniciens d'inspecter et de tester l'outil de coupe pour éviter les blessures.
  • 2023-07-20: Added the Oscillating Multi-Tool with a carbide teeth blade as an alternative to the cut-off tool when the cam bolt must be cut.
  • 2023-04-07: Updated tool info.

Special tool to remove the lower aft link to subframe cam bolt, if the bolt head is near the HV battery and the nut is toward the front of the vehicle:

  • 1522126-00-A 4" Extended Corner Cut-off Tool, for North America
  • 1522126-E0-A 4" Extended Corner Cut-off Tool, for Europe, Middle East, Africa

Alternatively, an Oscillating Multi-Tool with a carbide teeth blade can be used to cut the bolt.

Dépose

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Si le véhicule est doté de la suspension pneumatique, activez le mode « Jack » (Cric) sur l'écran tactile avant de soulever le véhicule, puis installez des chandelles.
  1. Remove the front left wheel. Voir Ensemble de roue (retrait et installation).
  2. Remove the front aero shield panel. Voir Panneau - écran aérodynamique - avant (retirez et remplacez).
  3. Use a 21 mm socket and Torx T40 to break loose the nut that attaches the LH lower aft link to the knuckle (torque 195 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Pour ne pas endommager le joint à rotule, immobilisez toujours la tige du joint avec une clé quand vous serrez ou desserrez le contre-écrou.
    Figure 1. LH shown, RH similar; some components hidden for clarity
  4. Use a 21 mm socket and wrench to remove the bolt and nut that attach the front spring module to the LH lower aft link (torque 140 Nm).
    Figure 2. LH shown, RH similar; some components hidden for clarity
  5. Remove and discard the nut and washer that attach the LH lower aft link to the knuckle (torque 195 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Pour ne pas endommager le joint à rotule, immobilisez toujours la tige du joint avec une clé quand vous serrez ou desserrez le contre-écrou.
    Figure 3. LH shown, RH similar; some components hidden for clarity
  6. Use a 21 mm socket and 22 mm wrench to remove the cam bolt and nut that attaches the LH lower aft link to the subframe (torque 130 Nm).
    Informational PurposesAn informational icon, calling your attention
    Note
    If the bolt head is facing towards the HV battery, it cannot be removed without being cut off. Refer to Aft Link (Cut Bolt) before continuing.
    Informational PurposesAn informational icon, calling your attention
    Note
    The labor for cutting the aft link cam bolt is not included in the labor for replacing the lower aft link. Correction code 31013907 should be added as a separate item on the Repair Order to account for the additional labor.
    Figure 4. Bolt head toward the front of the vehicle and nut near the HV battery (LH shown, RH similar; some components hidden for clarity)
  7. Remove the LH lower aft link from the vehicle.

Installation

Warning IconA warning icon, calling your attention to a possibly risky situation
CAUTION
Serrez complètement les écrous et boulons de suspensions uniquement quand le véhicule se trouve sur un pont élévateur à quatre poteaux et que la suspension est à hauteur normale.
  1. Maneuver the aft link into position and then install the cam bolt and nut that attach the LH lower aft link to the subframe. Hand tighten the cam bolt and nut.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Make sure that the bolt head is facing the front of the vehicle if the HV battery was removed for any reason during another repair. Failure to orient the bolt correctly can result in unnecessary increased labor in the future.
    Informational PurposesAn informational icon, calling your attention
    Note
    The fasteners are torqued later as part of the alignment check.
    Informational PurposesAn informational icon, calling your attention
    Note
    If a new cam bolt and nut are needed but constrained, use 1608802-00-C (cam) and 1610820-00-B (washer) from Model S/X (2021+) instead.

    2007106 has a shiny washer, 1608802-00-C has a gray dull washer

    Figure 5. Bolt head toward the front of the vehicle and nut near the HV battery (LH shown, RH similar; some components hidden for clarity)
  2. Use a 21 mm socket and Torx T40 to install a new nut and washer to attach the LH lower aft link to the knuckle (torque 195 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Pour ne pas endommager le joint à rotule, immobilisez toujours la tige du joint avec une clé quand vous serrez ou desserrez le contre-écrou.
    Figure 6. LH shown, RH similar; some components hidden for clarity
  3. Install the bolt and nut that attach the front spring module to the LH lower aft link. Hand tighten the bolt and nut.
    Informational PurposesAn informational icon, calling your attention
    Note
    The fasteners are torqued later as part of the alignment check.
    Figure 7. LH shown, RH similar; some components hidden for clarity
  4. Install the front aero shield panel. Voir Panneau - écran aérodynamique - avant (retirez et remplacez).
  5. Install the front left wheel. Voir Ensemble de roue (retrait et installation).
  6. Transfer the vehicle to a 4 post lift. Voir Soulever le véhicule - pont élévateur à 4 colonnes.
  7. Reportez-vous aux tableaux des exigences d’alignement pour déterminer si une vérification du parallélisme EPAS ou une vérification du parallélisme des quatre roues doit être effectuée. Si effectué, ajoutez la vérification/ajustement d'alignement en tant qu'activité séparée. Voir Exigences de réglage de la géométrie - Suspension.

Aft Link (Cut Bolt)

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Avant de couper le boulon, l'outil de coupe doit être inspecté et testé pour garantir sa sécurité d'utilisation.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
When cutting the bolt, wear appropriate Personal Protective Equipment (PPE) that includes safety goggles, face shield, gloves, dust mask or respirator, protective long sleeve (non-synthetic) shirt, and hearing protection.
Informational PurposesAn informational icon, calling your attention
Remarque
The labor for cutting the aft link cam bolt is not included in the labor for replacing the lower aft link. Correction code 31013907 should be added as a separate item on the Repair Order to account for the additional labor.
  1. Use a 22 mm wrench and 21 mm socket to remove the nut that attaches the LH aft link to the subframe.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The bolt cannot be removed because the HV battery is blocking it.
  2. Slide the bolt out from the aft link until the bolt head is nearly touching the HV battery. This exposes the body of the bolt, which can be cut to allow the bolt to be removed.
  3. Position the tool to begin cutting the bolt.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    Make sure the tool is not able to cut into the HV battery or subframe.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    The tool may create a considerable amount of sparks; make sure the surrounding area is free of flammable or combustible items.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    If using a cut-off tool, make sure to position the guard between the bolt head and the subframe mount.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The guard on the cut-off tool can be adjusted by pressing the lever on the cut-off tool head and rotating the guard.
  4. Cut through the body of the aft link bolt to remove the bolt head.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    When cutting the bolt, wear appropriate Personal Protective Equipment (PPE) that includes safety goggles, face shield, gloves, dust mask or respirator, protective long sleeve (non-synthetic) shirt, and hearing protection.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    The tool and blade will be hot. Do not touch the tool with an unprotected hand and avoid placing the tool on or near combustible or flammable items.
  5. While continuing to wear PPE, use pliers to remove the body of the cam bolt from the aft link and subframe.