20/12/2023 17:13:42

Bracket - Radar - Front (DAS 1/2) (Remove and Replace)

Code de correction

  • 2023-06-16: Replaced Toolbox 2 panels with Toolbox 3 routines.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Dépose

  1. Using MCU, set suspension to very high and press, open hood.
  2. Exit vehicle and open hood.
  3. Remove underhood aprons.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons.
  4. Release fascia to lower front aero shield.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x Push clips, 2x bolts, 10mm, 3 Nm.
  5. Remove bolts securing fascia to upper grill.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm.
  6. Remove the front T badge.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T25, 5 Nm, Done to prevent scratching of the front fascia chrome trim.
  7. Turn wheel fully to the right, to gain access to LF wheel liner clips.
  8. Remove front side of wheel liner to gain access to garnish bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x Push clips.
  9. Release the LH lower front of fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x Push clips, 2x bolts, 10mm, 1.5 Nm.
  10. Starting from the rear, carefully pull the LH fender garnish away from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x Heart flex clips, 1x connector.
  11. Remove the screw that secures fascia to LF fender.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  12. Pull LH fascia away from fender.
  13. Turn wheel fully to the left, to gain access to RF wheel liner clips.
  14. Remove front side of RF wheel liner to access garnish bolts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x Push clip.
  15. Release the RH lower front of fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x Push clips, 2x bolts, 10mm, 1.5 Nm.
  16. Starting from the rear, carefully pull the RH fender garnish away from the vehicle to release.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    5x Heart flex clips, 1x locking connection.
  17. Remove the screw that secures fascia to RF fender.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x screw, T25, 1.5 Nm.
  18. Pull RH fascia away from fender.
  19. Remove fascia by starting on the LH side of the vehicle, release the clips that secure the front fascia by pulling the fascia up and away from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x Fascia harness connection, Recommend assistance to hold fascia in place while releasing connection to prevent damage.
  20. Disconnect the radar sensor.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, squeeze lock tabs on both sides of the connector and pull straight down.
  21. Remove the radar support bracket from the front of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x Wire harness attachment clip, 3x bolts,10mm, 6.5 Nm.
  22. Gently pry up the tabs on the top of the radar bracket. Gently release the radar sensor forward from the bracket.

Installation

  1. Install new radar sensor to the radar bracket.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Ensure radar is fully seated in the radar bracket prior to installation.
  2. Install the radar bracket with radar onto the front of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x bolts,10mm, 6.5 Nm, 1x clip, ensure harness clip is secured to radar bracket.
  3. Make connection at radar sensor.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector.
  4. Using MCU apply standard suspension level.
  5. Perform Four Wheel Alignment Check and Adjust (with Air Suspension).
    Informational PurposesAn informational icon, calling your attention
    Remarque
    FRT per correction code-31000100.
  6. Measure vertical alignment of the radar by placing bubble tool along the top of the sensor’s front surface.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Check the bubble on the long portion of the bubble tool. The radar sensor is calibrated vertically if the bubble is centered between the black lines. If necessary, adjust the vertical set screw until the bubble level indicates vertical calibration has been achieved, labeled 2 in attached image.
  7. Connect the fascia harness and fully seat fascia.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Recommend assistance to hold fascia in place while making connection to prevent damage.
  8. Install bolts securing fascia to upper grill.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 4 Nm.
  9. Install the screws that secure fascia to fender on both sides of the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x screws, T25, 1.5 Nm.
  10. Install the Front T Badge.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, T25, 5 Nm.
  11. Install fascia to lower front aero shield.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x Push clips, 2x bolts, 10mm, 3 Nm, ensure tabs from fascia to aeroshield are properly aligned.
  12. Install the RH fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm, 1x push clip, 1x connector; make sure to fully seat the fog light duct to the fender garnish.
  13. Secure RF wheel liner to fascia and fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x Push clip, Ensure fender liner is seated behind inner lip of fender garnish.
  14. Turn wheel fully to the right.
  15. Install the LH fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 1.5 Nm, 1x push clip, 1x connector; make sure to fully seat the fog light duct to the fender garnish.
  16. Secure LF wheel liner to fascia and fender garnish.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x clips, Ensure fender liner is seated behind inner lip of fender garnish.
  17. Close hood.
  18. Connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3 (Connecter et déconnecter).
  19. Unlock the vehicle gateway. See Déverrouillage de passerelle.
  20. In Toolbox 3, click Dashboards > Service Tools > DTCs, and then select the type of DTCs to read.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If uncertain, click Check All.
  21. Click Read DTCs to display the DTCs.
  22. If necessary, power cycle the vehicle.
  23. Click Clear DTCs to clear the DTCs.
  24. Perform a front radar calibration. See GUID-63D02AAC-4A5F-4F90-AA01-582A1B6EB91C.html.
  25. Disconnect the laptop with Toolbox 3 from the vehicle. See Toolbox 3 (Connecter et déconnecter).
  26. Exit vehicle and open hood.
  27. Install under hood aprons.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    4x aprons.
  28. Close hood.
  29. Close the driver's front door.
  30. Perform vehicle road test.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Per current FRT (00040100) 0.3 hrs, Check operation of vehicle and any related repairs.