Code de correction 13034102

1. Open LH rear door

   

2. Move LH 2nd row seat fully forward using easy entry mode

   

3. Open liftgate

   

4. Remove rear load floor

   

5. Remove trunk board

   

6. Fold down LH 3rd row seat
   Remarque

   Press button located on LH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position

   

7. Fold down RH 3rd row seat
   Remarque

   Press button located on RH 3rd row seat back assembly near headrest, fold seat back down towards front of vehicle into a flat position

   

8. Remove trunk floor carpet

   

9. Drill out rivets securing rear seat back carpet to LH 3rd row seat
   Remarque

   2x rivets, Use vacuum to collect debris while drilling out rivets, Use 3/16" or 3mm drill bit

   

   

10. Remove rear seat back carpet from LH 3rd row seat
    Remarque

    9x clips

    

11. Release lower section of LH 3rd row seat upholstery
    Remarque

    4x tabs, 2x, fir tree clips, 1x J hook, Release tabs by pulling inward and up

    

    

    

    

12. Disconnect LH 3rd row seat connector
    Remarque

    1x connector, 1x clip

    

13. Re-route LH 3rd row seat connector through lower section of upholstery

    

14. Connect LH 3rd row seat connector
    Remarque

    1x connector, Route around seat upholstery

    

15. Unfold LH 3rd row seat into upright position
    Remarque

    Leave headrest in folded position

    

16. Remove upper half of LH 3rd row seat upholstery
    Remarque

    Release J-hook clip around edges of upholstery

    

    

17. From the 3rd row, pull seat cover and foam upward to access actuator
    Remarque

    Use fold function to feed bottom of seat upholstery forward, Use caution to not snag J-hooks, Actuator is located on the front side of the seat back under the upholstery and cushion assembly

    

    

    

18. Release seat recliner cable from bracket
    Remarque

    Cut zip tie and slide cable to release

    

    

19. Release seat recliner cable from LH 3rd row actuator pulley
    Remarque

    Note direction of actuator pulley

    

    

20. Remove 3rd row seat recliner actuator pulley
    Remarque

    Part is directional

    

21. Install new LH 3rd row recliner seat actuator pulley
    Remarque

    Align pulley to actuator gear, Locking clip and pulley are directional

    

    

22. Connect seat recliner cable to actuator pulley

    

23. Install seat recliner cable onto seat frame
    Remarque

    Secure with cable tie

    

    

24. Fold cushion and upholstery assembly down
    Remarque

    2x iso fix bars, Using folding function to assist with tucking upholstery, Ensure iso fix bars are fed through upholstery and seat belt does not get caught

    

    

    

25. Install upper half of LH 3rd row seat upholstery
    Remarque

    Fold seat to workable position, Start at one end and fold J hook inwards until the other end of the upholstery is tucked, Press firmly along J hook to seat fully

    

    

26. Disconnect LH 3rd row seat connector
    Remarque

    1x connector

    

27. Route LH 3rd row seat connector through seat upholstery

    

28. Connect LH 3rd row seat connector
    Remarque

    1x connector, 1x clip

    

29. Secure lower half of upholstery
    Remarque

    4x tabs, 2x, fir tree clips, 1x J hook

    

30. Install rear seat back carpet onto LH 3rd row seat
    Remarque

    9x clips

    

    

31. Install rivets into LH 3rd row seat back carpet
    Remarque

    2x rivets, Plastics rivet replaces metal rivet/washer combo

    

    

    

    

32. Reinstall front lower carpet trim panel
    Remarque

    Secure 3rd row seat wiring harnesses to panel

    

33. Install trunk board

    

34. Install rear load floor

    

35. Close liftgate

    

36. Move LH 2nd row seat from the easy entry position to the regular upright seating position
    Remarque

    Slide seat track backwards by pushing towards rear of vehicle, Fold upper seat backwards until locked in an upright position

    

37. Close LH Falcon door