2026-06-10

Scheinwerfer (SAE-bis-global) – Scheinwerfer-Baugruppe – Paar (Nachrüsten)

Korrekturcode 174001060,72 HINWEIS: Sofern im Verfahren nicht ausdrücklich anders angegeben, spiegeln der obige Korrekturcode und die FRT den gesamten für die Durchführung dieses Verfahrens erforderlichen Aufwand wider, einschließlich der damit verbundenen Verfahren. Schichten Sie keine Korrekturcodes, wenn Sie nicht ausdrücklich dazu aufgefordert werden. HINWEIS: Unter Richtzeiten erfahren Sie mehr über FRTs und wie sie erstellt werden. HINWEIS: Siehe Persönlicher Schutz, um sicherzustellen, dass Sie die richtige persönliche Schutzausrüstung tragen, wenn Sie das folgende Verfahren durchführen. HINWEIS: Siehe Maßnahmen zur Ergonomie für sichere und gesunde Arbeitsmethoden.

  • 2026-05-22: Removed reference to obsoleted Tech Note TN-24-17-002 and added some additional info from TN-24-17-002 on the retrofit.
  • 2024-06-27: Updated Toolbox 3 headlamps configuration "Global" direction.
Informational PurposesAn informational icon, calling your attention
Anmerkung
For proper headlamp operation in Model 3 vehicles, both headlamps must be of the same type (Global or SAE), and the vehicle software configuration must match the installed headlamp type. If one headlamp is damaged, and the replacement headlamp is not the same type (Global or SAE) as the undamaged headlamp, the undamaged headlamp must also be replaced. If an SAE type headlamp is damaged, replace both the damaged and the undamaged SAE headlamps with Global headlamps.

Nachrüstung

  1. Open the LH front door.
  2. Lower the LH front window.
  3. Remove the LH and RH headlights. See Scheinwerfer – LH (Ausbauen und Ersetzen).
  4. Install the new LH and RH headlights. See Scheinwerfer – LH (Ausbauen und Ersetzen).
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Do not adjust the headlights at this time. Headlight adjustment will be performed later in this procedure.
  5. If not already performed, enable Service Mode through the touchscreen. See Service-Modus.
  6. Enable Service Mode +. See Service-Modus +.
  7. In Toolbox 3, click on the Dashboards tab, search for “infotainment”, click Infotainment Dashboard > Vehicle Configuration > headlamps, and then change the "headlamps" configuration to "GLOBAL".
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    If you do not see this configuration displayed, update the vehicle to software version 2024.20 or later.
  8. On the vehicle touchscreen, perform a software reinstall concurrently with the rest of the steps in this procedure. See Neuinstallation der Software – Touchscreen.
  9. If the vehicle is equipped with a Virtual Pitch Sensor (VPS), in Toolbox 3, click the Actions tab, search for “PROC_ICE_X_SET-VIRTUAL-PITCH-SENSOR”, and then click Change leveling system of Virtual Pitch Sensor.
    Informational PurposesAn informational icon, calling your attention
    Anmerkung
    Make sure the vehicle is running firmware version 2024.8.9 or later to run this routine.
  10. Click Run and allow the routine to complete. Click X at the top right of the window to exit once the routine is complete.
  11. In Toolbox 3, go to Tools > Vehicle Configuration > headlightLevelerType and confirm the "headlightLevelerType" configuration is "VIRTUAL_PITCH_SENSOR".
  12. Disconnect the laptop from the vehicle. See Toolbox (Verbinden und Trennen).
  13. Adjust the headlights. See Scheinwerfer – Einstellen – Global (Werkzeugmethode).
  14. Disable Service Mode through the touchscreen. See Service-Modus.
  15. Raise the LH front window.
  16. Close the LH front door.