Código de corrección 17100802 2.64 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

1. Open all four doors
2. Lower all four windows
3. Open liftgate
4. Release 2nd row seat cushion
   Nota

   Lift front edge of seat cushion upward to release foam from frame, Pull towards front of vehicle then tilt bench against 40/60 back

   

5. Remove rear load floor

   

6. Remove front load floor

   

7. Remove trunk sill trim
   Nota

   4x clips

   

8. Remove LH load floor bracket
   Nota

   3x tabs, 2x clips

   

   

9. Remove LH trunk pocket bracket
   Nota

   1x push clip, 5x alignment tabs

   

10. Fold the 60 seat in down position
    Nota

    Protect the seat back upholstery if necessary, Do not put weight on seat in folded position without cushion present due to risk of bending the locator tab on the frame

    

11. Release top edge of LH trunk side trim and disconnect 12V outlet and trunk switch connectors
    Nota

    6x clips, 2x connectors, Trim part may slightly differ, by vehicle build location

    

    

12. Release remaining clips and remove LH trunk side trim
    Nota

    1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar

    

    

13. Remove LH upper C-pillar trim
    Nota

    6x clips, Guide front upper corner groove out from headliner and place trim aside

    

14. Remove RH load floor bracket
    Nota

    3x tabs, 2x clips

    

    

15. Remove RH trunk pocket bracket
    Nota

    1x push clip, 5x alignment tabs

    

16. Fold the 40 seat in down position
    Nota

    Protect the seat cushion, Do not put weight on seat in folded position without cushion present due to risk of bending the locator tab on the frame

    

17. Release clips and remove RH trunk side trim
    Nota

    1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar

    

    

    

18. Remove RH upper C-pillar trim
    Nota

    6x clips, Guide front upper corner groove out from headliner and place trim aside

    

    

    

19. Remove LH mid A-pillar assembly
    Nota

    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove

    

20. Remove clip securing LH lower A-pillar trim
    Nota

    1x push clip

    

21. Remove LH lower A-pillar trim
    Nota

    6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel

    

22. Release LH front door seal from body

    

23. Remove clip securing LH front cabin carpet to body
    Nota

    1x clip

    

24. Pull LH front cabin carpet away from A-pillar to access LH front seat connector

    

25. Move LH front seat forward
26. Remove RH mid A-pillar assembly
    Nota

    1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove

    

27. Remove clip securing RH lower A-pillar trim
    Nota

    1x push clip

    

28. Remove RH lower A-pillar trim
    Nota

    6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel

    

29. Release RH front door seal from body

    

30. Remove clip securing RH front cabin carpet to body
    Nota

    1x clip

    

31. Pull RH front cabin carpet away from A-pillar to access RH front seat connector

    

32. Move RH front seat forward
33. Release seat belt retractor from RH front seat
    Nota

    Insert special removal tool into the bottom of the retractor to release

    

34. Release seat belt retractor from LH front seat
    Nota

    Insert special removal tool into the bottom of the retractor to release

    

35. Remove LH front seat rear fasteners
    Nota

    2x patch bolts, T45P, 33.5 Nm, Discard after removal

    

36. Move LH front seat backward
37. Remove LH front seat front fasteners
    Nota

    2x patch bolts, T45P, 33.5 Nm, Discard after removal

    

38. Adjust position of LH front seat for easy removal
    Nota

    Move seat to middle of track at most upright position
39. Remove RH front seat rear fasteners
    Nota

    2x patch bolts, T45P, 33.5 Nm, Discard after removal

    

40. Move RH front seat backward
41. Remove RH front seat front fasteners
    Nota

    2x patch bolts, T45P, 33.5 Nm, Discard after removal

    

42. Adjust position of RH front seat for easy removal
    Nota

    Move seat to middle of track at most upright position
43. Open hood
44. Remove rear apron
    Nota

    14x clips

    

    

45. Power off vehicle from center display
    Nota

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
46. Disconnect 12V negative terminal and first responders loop
    Nota

    1x nut, 10mm, 6 Nm, 1x connector, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V, Negative terminal should be disconnected before FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

47. Disconnect LH front seat harness from VC left
    Nota

    1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC left, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged

    

    

48. Remove LH front seat harness from LH footwell support bracket
    Nota

    2x retaining clips

    

    

49. Release LH front seat harness from LH front sill panel harness bracket
    Nota

    5x clips

    

50. Pull LH front seat harness from under LH front cabin carpet

    

51. Remove LH front seat from vehicle
    Nota

    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

    

52. Disconnect RH front seat harness from VC right
    Nota

    1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC right, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged

    

    

53. Remove RH front seat harness from RH footwell support bracket
    Nota

    2x retaining clips

    

    

54. Release RH front seat harness from lower A 12V bracket
    Nota

    5x clips

    

55. Pull RH front seat harness from under RH front cabin carpet

    

56. Remove RH front seat from vehicle
    Nota

    Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

    

57. Remove LH console side panel carpet
    Nota

    11x clips, 2x guide pins, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged

    

    

58. Remove LH front exterior hardware from center console
    Nota

    2x bolts, 10mm, 7 Nm

    

59. Remove console lower rear panel
    Nota

    5x clips

    

60. Remove LH rear exterior hardware from center console
    Nota

    1x bolt, 10mm, 7 Nm

    

61. Remove RH rear exterior hardware from center console
    Nota

    1x bolt, 10mm, 7 Nm

    

62. Remove RH console side panel carpet
    Nota

    12x clips, 2x locating pins, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged

    

    

63. Remove RH front exterior hardware from center console
    Nota

    2x bolts, 10mm, 7 Nm

    

64. Disconnect harness from rear of center console
    Nota

    1x connector

    

65. Disconnect USB harness at right front of center console
    Nota

    1x USB connector

    

66. Remove center console from vehicle
    Nota

    Verify rotating lids are in closed position, Recommend assistance, Tilt rear of console upward, Pull assembly towards rear of vehicle

    

    

67. Release LH upper B-pillar assembly and move aside
    Nota

    4x clips, Pull the bottom of the upper B-pillar toward inside of the vehicle then pull the top to release the remaining clips

    

68. Partially remove LH rear door seal

    

69. Remove LH rear sill trim
    Nota

    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim, Trim part may slightly differ, by vehicle build location

    

    

70. Remove clip securing LH lower B-pillar to body
    Nota

    1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

    

71. Remove the LH lower B-pillar assembly
    Nota

    6x clips, Pull the top of B-pillar to release top clips then work your way to bottom clips

    

72. Release clips securing the RH upper B-pillar assembly and move aside
    Nota

    4x clips, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips

    

    

73. Partially remove RH rear door seal
    Nota

    Pillar and sill trim have tabs seated underneath seal

    

74. Remove RH rear sill trim
    Nota

    5x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of RH rear sill trim working your way back towards rear of sill trim

    

    

75. Remove clip securing RH lower B-pillar to body
    Nota

    1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

    

76. Remove the RH lower B-pillar assembly
    Nota

    6x clips, Pull the top of B-pillar to release top clips then work your way to bottom clips

    

77. Remove rear floormat

    

78. Remove clips securing rear main cabin carpet to vehicle
    Nota

    3x push clips

    

79. Remove rear main cabin carpet from vehicle
    Nota

    Pull up at the rear of rear main carpet and slide back, Remove from LH rear door

    

    

    

    

80. Remove screw and clips securing LH footwell cover
    Nota

    2x push clips, 1x screw, T20, 2.5 Nm

    

81. Remove connectors from LH footwell cover and remove from vehicle
    Nota

    3x tabs, 1x Ethernet connector, 1x puddle light connector

    

82. Remove fasteners securing driver knee air bag to vehicle
    Nota

    2x push clips, 2x screws, T20, 2 Nm, 4x patch bolts, E10, 8 Nm, Discard after removal, Support the knee air bag while lowering, The connector / harness length is very short

    

    

    

    

83. Disconnect the driver knee air bag and remove from vehicle
    Nota

    1x connector, Release locking tab, Then release squib from air bag, Support air bag while disconnecting, Connector release may vary

    

    

    

84. Remove the LH footwell air duct

    

    

85. Remove LH front floormat

    

86. Remove clips securing LH front cabin carpet to vehicle
    Nota

    2x clips

    

87. Remove LH front cabin carpet from vehicle
    Nota

    Lift up rear edge of carpet then slide out towards rear of vehicle, be cautious and avoid foam below catching on seat risers

    

88. Remove LH upper A-pillar trim
    Nota

    3x clips, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove

    

    

    

    

89. Remove LH sun visor bracket cover
    Nota

    4x clips, Extending the sun visor may allow for extra working room

    

90. Remove LH sun visor fastener
    Nota

    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room

    

91. Remove LH sun visor from headliner area
    Nota

    Fold sun visor to the closed and folded down position but do not latch in place

    

92. Disconnect LH sun visor connector
    Nota

    1x connector

    

93. Remove RH upper A-pillar trim
    Nota

    3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove

    

    

    

    

94. Remove RH sun visor bracket cover
    Nota

    4x clips, Extending the sun visor may allow for extra working room

    

95. Remove RH sun visor fastener
    Nota

    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room

    

96. Remove RH sun visor from headliner area
    Nota

    Fold sun visor to the closed and folded down position but do not latch in place

    

97. Disconnect RH sun visor connector
    Nota

    1x connector

    

98. Remove lower quad cam cover
    Nota

    4x tabs, Press on the side of the cover with a trim tool to release some of the tabs

    

99. Remove tether from lower quad cam cover
    Nota

    1x hook, Guide hook through anchor on quad cam cover

    

100. Disconnect rear view mirror connector
     Nota

     1x connector

     

101. Remove rear view mirror
     Nota

     1x bolt, T20, 2.5 Nm

     

     

102. Push open LH coat hook

     

     

103. Open LH coat hook screw cover
     Nota

     1x locking tab

     

104. Remove LH coat hook screw
     Nota

     1x screw, T20, 1.0 Nm

     

105. Push open RH coat hook

     

     

106. Open RH coat hook screw cover
     Nota

     1x locking tab

     

     

107. Remove RH coat hook screw
     Nota

     1x screw, T20, 1.0 Nm

     

108. Release headliner from body
     Nota

     11x clips, Recommend assistance, Headliner will be partially supported by safety tethers at B-pillars and 2x tether clips at rear corners

     

     

109. Disconnect J5 body connector
     Nota

     1x connector, Release lock then remove

     

110. Disconnect J2 body connector
     Nota

     1x connector, Release lock then remove

     

111. Disconnect J4 body connector
     Nota

     1x connector, Release lock then remove

     

112. Disconnect brake switch
     Nota

     1x connector

     

113. Disconnect accelerator pedal connector
     Nota

     1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector

     

114. Remove accelerator and brake pedal harness clips
     Nota

     4x clips

     

     

115. Disconnect headliner harness
     Nota

     1x connector

     

116. Disconnect white connector X909 from front harness
     Nota

     1x connector

     

117. Remove LH body harness clips from LH A-pillar
     Nota

     3x clips

     

118. Release clips securing for LH body harness from below LH front seat
     Nota

     3x clips

     

     

119. Remove LH harness clips under front seats and center console
     Nota

     3x clips

     

120. Disconnect LH body harness from RCM
     Nota

     1x connector

     

121. Disconnect LH harness from RH body Harness
     Nota

     2x connectors,1x clip,Release red locking tabs

     

     

     

122. Disconnect the LH body harness connectors around lower B-pillar area
     Nota

     4x connectors, LH rear door harness, acceleration sensor, and LH seat belt

     

123. Remove the LH harness ground strap around LH lower B-pillar area
     Nota

     1x bolt, 10mm, 10 Nm

     

124. Remove LH harness clips from B-pillar area
     Nota

     6x clips

     

125. Release LH B-pillar applique from body to disconnect camera connector then remove from vehicle
     Nota

     1x fir tree clip, 2x clips, 2x connectors, Pull straight outwards to release from B-Pillar, Use caution not to damage the connectors

     

     

     

126. Remove the LH body harness clips around the below C-pillar area
     Nota

     4x clips

     

     

127. Disconnect logic connector at LH seat frame
     Nota

     1x connector

     

128. Disconnect LH 2nd row retractor connector
     Nota

     1x connector, 2 stage locking connector, Lift the red locking tab then release the connector

     

129. Remove the LH body harness clips around C-pillar area
     Nota

     4x clips

     

     

130. Disconnect LH side curtain air bag and liftgate power strut electrical connector from LH body harness
     Nota

     2x connectors

     

131. Release connectors from LH body harness to charge port ECU
     Nota

     2x connectors

     

132. Remove LH body harness clips around LH side trunk area
     Nota

     3x clips

     

133. Disconnect connectors from chargeport assembly
     Nota

     3x connectors, 1x red locking tab, 2x white locking tab

     

134. Remove the LH body harness ground strap below LH tail lamp
     Nota

     1x bolt, 10mm, 10 Nm

     

135. Remove LH liftgate stop
     Nota

     1x liftgate stop, Pull up to remove

     

     

136. Disconnect LH rear bodyside tail lamp assembly connector
     Nota

     1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

     

     

137. Remove nuts securing LH rear bodyside tail lamp assembly to vehicle
     Nota

     2x nuts, 8mm, 3.2 Nm

     

138. Remove LH rear bodyside tail lamp assembly from vehicle
     Nota

     2x studs, To ease removal use trim tool to release lamp from body near each stud. While releasing studs, Pull from opposite end of lamp.

     

     

139. Remove bolt securing LH corner of rear fascia to body
     Nota

     1x bolt, 10mm, 4 Nm

     

140. Remove RH liftgate stop
     Nota

     1x liftgate stop, Pull up to remove

     

141. Disconnect RH rear bodyside tail lamp assembly connector
     Nota

     1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

     

142. Remove nuts securing RH rear bodyside tail lamp assembly to vehicle
     Nota

     2x nuts, 8mm, 3.2 Nm

     

143. Remove RH rear bodyside tail lamp assembly from vehicle
     Nota

     2x studs

     

     

144. Remove bolt securing RH corner of rear fascia to body
     Nota

     1x bolt, 10mm, 4 Nm

     

145. Release rear fascia from rear diffuser
     Nota

     6x clips, 7x bolts, 10mm, 4 Nm

     

     

146. Remove LH rear fender garnish from vehicle
     Nota

     14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish

     

     

     

     

147. Remove bolt securing LH rear fascia to body
     Nota

     1x bolt, 8mm, 4 Nm

     

148. Remove RH rear fender garnish from vehicle
     Nota

     14x clips, Release from center of garnish and work your way outward towards both ends, Using clip prytool release yellow clips at rear of fascia to avoid damage to garnish

     

     

     

     

149. Remove bolt securing RH rear fascia to body
     Nota

     1x bolt, 8mm, 4 Nm

     

150. Release rear fascia from body and disconnect rear fascia harness then remove assembly from vehicle
     Nota

     1x connector, Slide red locking tab away from connector, Then depress black locking tab to release the connector. Recommend assistance, Place rear fascia on padded surface to avoid damage

     

     

     

151. Remove rear body harness from rear fascia center bracket
     Nota

     4x clips

     

     

152. Disconnect rear BLE
     Nota

     1x connector, 2 stage locking connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

     

153. Disconnect rear subframe and LH rear EPB connectors
     Nota

     2x connectors

     

154. Push the rear subframe portion of the LH body harness through the LH side trunk bulkhead
     Nota

     Harness passes through into trunk near rear section of LH rear wheel liner area

     

155. Remove the LH body harness from vehicle

     

156. Position the LH body harness into vehicle for installation

     

157. Push the rear harness seal through body and fully seat
     Nota

     Harness passes through into trunk near rear section of LH rear wheel liner area

     

158. Connect rear subframe and LH rear EPB connector
     Nota

     2x connectors

     

159. Connect rear BLE
     Nota

     1x connector, Engage locking tab

     

160. Install rear body harness onto rear fascia center bracket
     Nota

     4x clips

     

     

161. Connect and install rear fascia onto vehicle
     Nota

     1x connector, Engage red locking tab, Recommend assistance, Verify lower portion aligns with rear diffuser

     

     

     

     

162. Apply Loctite 222 onto rear diffuser bolts and secure rear fascia to rear diffuser
     Nota

     6x clips, 7x bolts, 10mm, 4 Nm

     

     

163. Install bolt securing RH rear fascia to body
     Nota

     1x bolt, 8mm, 4 Nm

     

164. Install RH rear fender garnish
     Nota

     14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

     

     

     

     

165. Install bolt securing LH rear fascia to body
     Nota

     1x bolt, 8mm, 4 Nm

     

166. Install LH rear fender garnsih
     Nota

     14x clips, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

     

     

     

     

167. Install bolt securing RH corner of rear fascia
     Nota

     1x bolt, 10mm, 4 Nm

     

168. Remove RH bodyside lamp connector gasket
     Nota

     1x gasket

     

169. Install RH bodyside lamp connector gasket
     Nota

     1x gasket

     

170. Remove upper T-stud gasket from RH bodyside lamp
     Nota

     1x gasket

     

171. Install upper T-stud gasket to RH bodyside lamp
     Nota

     1x gasket

     

172. Remove lower T-stud gasket from RH bodyside lamp
     Nota

     1x gasket

     

173. Install lower T-stud gasket to RH bodyside lamp
     Nota

     1x gasket

     

174. Install RH rear bodyside tail lamp assembly into vehicle
     Nota

     2x studs

     

     

175. Install nuts securing RH rear bodyside tail lamp assembly to vehicle
     Nota

     2x nuts, 8mm, 3.2 Nm

     

176. Connect the RH rear bodyside tail lamp assembly
     Nota

     1x connector, Engage locking tab

     

177. Install RH liftgate stop
     Nota

     1x liftgate stop, Align tab and push down to secure

     

178. Install bolt securing LH corner of rear fascia
     Nota

     1x bolt, 10mm, 4 Nm

     

179. Remove LH bodyside lamp connector gasket
     Nota

     1x gasket

     

180. Install LH bodyside lamp connector gasket
     Nota

     1x gasket

     

181. Remove upper T-stud gasket from LH bodyside lamp
     Nota

     1x gasket

     

182. Install upper T-stud gasket to LH bodyside lamp
     Nota

     1x gasket

     

183. Remove lower T-stud gasket from LH bodyside lamp
     Nota

     1x gasket

     

184. Install lower T-stud gasket to LH bodyside lamp
     Nota

     1x gasket

     

185. Install LH rear bodyside tail lamp assembly into vehicle
     Nota

     2x studs

     

     

186. Install nuts securing LH rear bodyside tail lamp assembly to vehicle
     Nota

     2x nuts, 8mm, 3.2 Nm

     

187. Connect the LH rear bodyside tail lamp assembly
     Nota

     1x connector, Engage locking tab

     

     

188. Install LH liftgate stop
     Nota

     1x liftgate stop, Align tab and push down to secure

     

189. Install the LH body harness ground strap below LH tail lamp
     Nota

     1x bolt, 10mm, 10 Nm

     

190. Install logic connectors to charge port assembly
     Nota

     3x connectors, 1x red locking tab, 2x white locking tab
191. Install LH body harness clips around LH side trunk area
     Nota

     3x clips

     

192. Install connectors from LH body harness to charge port ECU
     Nota

     2x connectors

     

193. Connect LH side curtain air bag and liftgate power strut electrical connector to LH body harness
     Nota

     2x connectors

     

194. Install the LH body harness clips around upper C-pillar area
     Nota

     4x clips

     

     

195. Connect LH 2nd row retractor connector
     Nota

     1x connector, 2 stage locking connector, Engage the red locking tab when the connector is fully seated

     

196. Connect logic connector at LH 60 seat frame
     Nota

     1x connector

     

197. Install the LH body harness clips around the below C-pillar area
     Nota

     4x clips

     

     

198. Connect camera connector then install LH B-pillar applique to vehicle
     Nota

     2x connectors, 1x fir tree clip, 2x clips, Align B-Pillar applique into position and secure clips into body, Use caution not to damage the connectors

     

     

     

199. Install LH harness clips onto B-pillar area
     Nota

     6x clips

     

200. Connect the LH body harness connectors around lower B-pillar area
     Nota

     4x connectors, LH rear door harness, acceleration sensor, and LH seat belt

     

201. Install the LH harness ground strap around LH lower B-pillar area
     Nota

     1x bolt, 10mm, 10 Nm

     

202. Connect LH harness to RH body Harness
     Nota

     2x connector,1x clip,Engage locking tabs

     

     

     

203. Install LH body harness to RCM
     Nota

     1x connector

     

204. Install LH harness clips under LH front seat and RH lower B-pillar area
     Nota

     3x clips

     

205. Install securing clips LH body harness beiow LH front seat
     Nota

     3x clips

     

     

206. Install LH body harness clips to LH A-pillar
     Nota

     3x clips

     

207. Connect J5 body connector
     Nota

     1x connector, Fully seat connector then engage lock

     

208. Connect J2 body connector
     Nota

     1x connector, Fully seat connector then engage lock

     

209. Connect J4 body connector
     Nota

     1x connector, Fully seat connector then engage lock

     

210. Connect white connector X909 to front harness
     Nota

     1x connector

     

211. Connect headliner harness
     Nota

     1x connector

     

212. Install accelerator and brake pedal harness clips
     Nota

     4x clips

     

     

213. Connect accelerator pedal connector
     Nota

     1x connector, Engage locking tab

     

214. Connect brake switch connector
     Nota

     1x connector

     

215. Install the LH footwell duct into HVAC module

     

216. Connect the driver knee air bag and install into vehicle
     Nota

     1x connector, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector

     

     

217. Install fasteners securing driver knee air bag to vehicle
     Nota

     4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 2x push clips

     

     

     

     

218. Install headliner to body
     Nota

     11x clips, Recommend assistance, Seat 2x clips at coat hooks when replacing headliner, Reseat primary seal at doors and liftgate to headliner

     

     

219. Install rear view mirror
     Nota

     1x bolt, T20, 2.5 Nm

     

220. Connect rear view mirror connector
     Nota

     1x connector

     

221. Install tether onto lower quad cam cover
     Nota

     1x hook, Guide hook through anchor on quad cam cover

     

222. Install quad camera lower cover
     Nota

     4x tabs, Install the tabs closest to the rearview mirror assembly and push the cover up to secure

     

223. Connect RH sun visor connector
     Nota

     1x connector

     

224. Install RH sun visor into headliner area
     Nota

     Fold sun visor to the closed and folded down position but do not latch in place

     

225. Install RH sun visor fastener
     Nota

     1x screw, T25, 3.5 Nm

     

226. Install RH sun visor bracket cover
     Nota

     4x clips

     

227. Install RH upper A-pillar trim
     Nota

     3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

     

     

     

     

228. Connect LH sunvisor connector
     Nota

     1x connector

     

229. Install LH sun visor into headliner area
     Nota

     Fold sun visor to the closed and folded down position but do not latch in place

     

230. Install LH sun visor fastener
     Nota

     1x screw, T25, 3.5 Nm

     

231. Install LH sun visor bracket cover
     Nota

     4x clips

     

232. Install LH upper A-pillar trim
     Nota

     3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim

     

     

     

     

233. Install LH coat hook screw
     Nota

     1x screw, T20, 1.0 Nm

     

234. Close LH coat hook screw cover
     Nota

     1x locking tab

     

235. Push LH coat hook closed

     

236. Install RH coat hook screw
     Nota

     1x screw, T20, 1.0 Nm

     

237. Close RH coat hook screw cover
     Nota

     1x locking tab

     

238. Push RH coat hook closed

     

     

239. Install LH upper C-pillar trim
     Nota

     6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim

     

     

     

     

240. Position LH trunk side trim and install lower clips
     Nota

     1x push clips, 5x clips, Guide front clip stanchions around LH C-pillar

     

     

241. Connect 12V outlet and trunk switch connector and seat top edge of LH trunk side trim
     Nota

     6x clips, 2x connectors

     

     

242. Install LH trunk pocket bracket
     Nota

     1x push clip, 5x alignment tabs

     

243. Install LH load floor bracket
     Nota

     3x tabs, 2x clips

     

     

244. Install RH upper C-pillar trim
     Nota

     6x clips, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarterglass, Seat trunk seal to edge of trim

     

     

     

     

245. Install RH trunk side trim
     Nota

     1x push clip, 11x clips, Guide front clip stanchions around RH C-pillar

     

     

     

246. Install RH trunk pocket bracket
     Nota

     1x push clip, 5x alignment tabs

     

247. Install RH load floor bracket
     Nota

     3x tabs, 2x clips

     

     

248. Install front load floor

     

249. Install rear load floor

     

250. Install trunk sill trim
     Nota

     4x clips, Seat seal around edge of trim

     

     

     

251. Fold the 60 seat into vertical position
     Nota

     Remove seat back protection if necessary

     

252. Fold 40 seat into vertical position
     Nota

     Remove seat cushion protection

     

253. Install rear main cabin carpet to vehicle
     Nota

     Position rear main carpet to floorboard and slide forward, Ensure rear main carpet tucks beneath front main carpet and air duct

     

     

     

     

254. Install clips securing rear main cabin carpet to vehicle
     Nota

     3x push clips

     

255. Install rear floormat

     

256. Install LH front cabin carpet

     

257. Install clips securing the LH front cabin carpet to vehicle
     Nota

     2x clips

     

258. Install connectors to LH footwell cover and position for installation
     Nota

     3x tabs, 1x Ethernet connector, 1x puddle light connector

     

     

     

259. Install screw and clips securing LH footwell cover
     Nota

     1x screw, T20, 2.5 Nm, 2x push clips

     

260. Install the RH lower B-pillar assembly
     Nota

     6x clips, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips

     

261. Install clip securing RH lower B-pillar to body
     Nota

     1x push clip, Clip goes through B-pillar and rear cabin carpet

     

262. Install RH rear sill trim
     Nota

     5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips

     

     

263. Install the RH upper B-pillar assembly
     Nota

     4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim

     

     

     

264. Install the LH lower B-pillar assembly
     Nota

     6x clips, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips

     

265. Install clip securing LH lower B-pillar to body
     Nota

     1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

     

266. Install LH rear sill trim
     Nota

     5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of LH rear sill trim into trunk side trim and work your way forward securing clips, Trim part may slightly differ, by vehicle build location

     

     

267. Reseat LH rear door seal
     Nota

     Seat pillar and sill trim tabs underneath seal

     

268. Reposition 2nd row seat cushion
     Nota

     Slide cushion rearward then align with buckles and foam with seat rail, Make sure cushion is fully seated with push & pull test

     

269. Install the LH upper B-pillar assembly
     Nota

     4x clips, Lower the seat belt slider to align it with the B-pillar panel, Insert top portion of upper B-pillar under the headliner to align the clips, Press the bottom to fully seat upper B-pillar to lower B-pillar, Make sure the seal correctly overlaps the trim

     

     

     

270. Install center console onto vehicle
     Nota

     Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place

     

271. Connect harness at right front of center console
     Nota

     1x USB connector

     

272. Connect harness to rear of center console
     Nota

     1x connector

     

273. Install RH front exterior hardware to center console
     Nota

     2x bolts, 10mm, 7 Nm

     

274. Install RH console side panel carpet
     Nota

     12x clips, 2x locating pins, Position side panel and align the front locator, then the rear locator, Push side panel towards console to install

     

     

275. Install RH rear exterior hardware to center console
     Nota

     1x bolt, 10mm, 7 Nm

     

276. Install LH rear exterior hardware to center console
     Nota

     1x bolt, 10mm, 7 Nm

     

277. Install console lower rear panel
     Nota

     5x clips

     

278. Install LH front exterior hardware to center console
     Nota

     2x bolts, 10mm, 7 Nm

     

279. Install LH console side panel carpet
     Nota

     11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install

     

     

     

     

280. Install LH front seat into vehicle
     Nota

     Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

     

     

281. Secure LH front seat harness under LH front cabin carpet

     

282. Install LH front seat harness along LH front sill panel harness bracket
     Nota

     5x clips

     

283. Install LH front seat harness onto LH footwell support bracket
     Nota

     2x clips

     

     

284. Connect LH front seat harness to VC left
     Nota

     1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated

     

     

285. Fully seat LH front cabin carpet

     

286. Install clip securing LH front cabin carpet to body

     

287. Install LH lower A-pillar trim
     Nota

     6x clips, 2 locating pins, Align front locating pin first

     

288. Install clip securing LH lower A-pillar trim
     Nota

     1x push clip

     

289. Install LH mid A-pillar assembly
     Nota

     1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim

     

290. Reseat LH front door seal along lower A-pillar trim

     

291. Install RH front seat into vehicle
     Nota

     Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim

     

     

292. Secure RH front seat harness under RH front cabin carpet

     

293. Install RH front seat harness along plastic guide
     Nota

     5x clips

     

294. Install RH front seat harness onto RH footwell support bracket
     Nota

     2x retaining clips

     

     

295. Connect RH front seat harness to VC right
     Nota

     1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated

     

     

296. Fully seat RH front cabin carpet

     

297. Install clip securing RH front cabin carpet to body
     Nota

     1x clip

     

298. Install RH lower A-pillar trim
     Nota

     6x clips, 2x locating pins, Align front locating pin first

     

299. Install clip securing RH lower A-pillar trim
     Nota

     1x clip

     

300. Install RH mid A-pillar assembly
     Nota

     1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim

     

301. Reseat RH front door seal along lower A-pillar trim

     

302. Connect first responder loop and 12V negative terminal
     Nota

     1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer

     

     

303. Install rear apron
     Nota

     14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

     

     

304. Close hood
305. Move LH front seat backward
306. Install LH front seat front fasteners
     Nota

     2x patch bolts, T45P, 33.5 Nm, Install new patch bolts

     

307. Move LH front seat forward
308. Install LH front seat belt retractor to seat
     Nota

     Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test

     

309. Install LH front seat rear fasteners
     Nota

     2x patch bolts, T45P, 33.5 Nm, Install new patch bolts

     

310. Move LH front seat to original position
311. Move RH front seat backward
312. Install RH front seat front fasteners
     Nota

     2x patch bolts, T45P, 33.5 Nm, Install new patch bolts

     

313. Move RH front seat forward
314. Install RH front seat belt retractor to seat
     Nota

     Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test

     

315. Install RH front seat rear fasteners
     Nota

     2x patch bolts, T45P, 33.5 Nm, Install new patch bolts

     

316. Move RH front seat to original position
317. Close liftgate
318. Raise all four windows
319. Close all four doors
     Nota

     If 12V is powered up, Unlatch rear doors before closing