01/03/2023 11:39:29

Guía del asiento - Exterior - Asiento de la 2.ª fila - Lado izquierdo (7 plazas) (Desinstalación y sustitución)

Código de corrección 13020332 0.84 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Retirar

  1. Remove the LH 2nd row seat assembly from the vehicle. See Conjunto de asiento - 2.ª fila - Lado izquierdo (7 plazas) (Desinstalación y sustitución).
  2. Remove the push clip from the front of the LH 2nd row seat outer sideshield assembly.
    Consejo: Use a pick to remove the push clip from the bottom side of the outboard cover.
  3. Release the clip that attaches the LH 2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector, and then remove the sideshield from the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  4. Release the clips (x3) that attach the LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from the seat assembly.
  5. Remove the LH 2nd row seat toe kick cover. See Cubierta - Zona de los pies - Asiento de la 2.ª fila - Lado izquierdo (7 plazas) (Desinstalación y sustitución).
  6. Remove the LH 2nd row seat back panel. See Panel trasero - Asiento de la 2.ª fila - Lado izquierdo (Desinstalación y sustitución).
  7. Remove the center 2nd row seat back panel. See Panel trasero - Asiento de la 2.ª fila - Centro/20 (5 plazas) (Desinstalación y sustitución).
  8. Disconnect the LH 2nd row seat harness electrical connectors (x7), and then release the clip that attaches the harness to the seat frame.
  9. Release the seat cables (x4) from the LH 2nd row seat EZ entry actuator.
  10. Remove the push clips (x2) from the LH 2nd row seat cushion pan.
  11. Remove the center 2nd row lumbar bun. See Relleno lumbar - 2.ª fila - Central/20 (Desinstalación y sustitución).
  12. Remove the center 2nd row seat back pivot clamps. See Abrazaderas de pivote - Respaldo - 2.ª fila - Central/20 (Desinstalación y sustitución).
  13. Lift the center 2nd row seat back upward to remove it from the seat assembly.
  14. Manually release the center seatback latch.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use a small screwdriver to manipulate the center seatback latch to release it.
  15. Remove the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    • Vaso Torx T25
  16. Remove the LH 2nd row seat headrest trim. See Reposacabezas - 2.ª fila - Exterior - Izquierdo (Desinstalación y sustitución).
  17. Remove the LH 2nd row headrest adjustment guide. See Guía de ajuste - Reposacabezas - 2.ª fila (Desinstalación y sustitución)
  18. Remove the LH 2nd row seat headrest guide lock. See Bloqueo de guía - Reposacabezas - 2.ª fila (Desinstalación y sustitución).
  19. Release the clips (x4) that attach the LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from the assembly.
  20. Lift the rear of the LH 2nd row seat cushion assembly, and then slide the cushion toward the front of the seat to remove it from the seat assembly.
  21. Use a pick to manually move the LH 2nd row seat into easy entry position.
  22. Remove and discard the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
  23. With one hand, engage the towel bar, move the outer seat track rearward with the other hand until the groove on the LH seat podium releases from the outer seat track, and then lift the LH 2nd row seat podium upward while removing it from the inner seat track.
  24. Release the clips (x2) that attach the LH 2nd row seat easy entry actuator cable to the RH easy entry latch.
  25. Remove the nuts that attach the LH 2nd row seat outer seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 13 mm
  26. Slide the LH 2nd row seat outer seat track outwards and away from the towel bar to remove it from the assembly.

Instalar

  1. Position the LH 2nd row seat inner seat track into the seat assembly.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure the seat track is properly seated.
  2. Install the nuts that attach the LH 2nd row seat outer seat track to the seat frame assembly.
    37 Nm (27.3 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 13 mm
  3. Secure the clips (x2) that attach the LH 2nd row seat easy entry actuator cable to the RH easy entry latch.
  4. Install the groove on the LH 2nd row seat podium to the inner seat track, and then align the groove on the podium to the outer seat track. Engage the towel bar with one hand, and then move the outer seat track inward until the groove on the podium engages to the seat track.
  5. Install new the bolts (x2) that attach the LH 2nd row seat podium to the seat tracks.
    37 Nm (27.3 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
  6. Position the LH 2nd row seat onto the seat tracks, and then push the seat downward to latch the floor latches.
  7. Starting at the rear of the seat, position the LH 2nd row seat pan onto the seat frame.
  8. Install the fasteners (x4) that attach the LH 2nd row seat seat pan to the seat frame.
    6 Nm (4.4 lbs-ft)
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Nota
    The 10 mm bolts are torqued to 6 Nm. The T25 screws are torqued to 1.5 Nm.
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
    • Vaso Torx T25
  9. Position the LH 2nd row seat back to the seat assembly, and then install the clips (x4) that attach the seat back to the assembly.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure the bottom retainers slide into position.
  10. Install the LH 2nd row seat headrest guide lock. See Bloqueo de guía - Reposacabezas - 2.ª fila (Desinstalación y sustitución).
  11. Install the LH 2nd row headrest adjustment guide. See Guía de ajuste - Reposacabezas - 2.ª fila (Desinstalación y sustitución)
  12. Install the LH 2nd row seat headrest trim. See Reposacabezas - 2.ª fila - Exterior - Izquierdo (Desinstalación y sustitución).
  13. Install the center 2nd row seat back pivot clamps. See Abrazaderas de pivote - Respaldo - 2.ª fila - Central/20 (Desinstalación y sustitución).
  14. Install the center 2nd row lumbar bun. See Relleno lumbar - 2.ª fila - Central/20 (Desinstalación y sustitución).
  15. Position the LH 2nd row seat outer sideshield to the seat assembly, connect the electrical connector, and then secure the clip.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
  16. Install the push clip to the front of the LH 2nd row seat outer sideshield assembly.
    Consejo: Use a pick to remove the push clip from the bottom side of the outboard cover.
  17. Install the clips (x3) that attach the LH 2nd row seat inboard outer trim to the LH 2nd row seat.
  18. Install the center 2nd row seat back panel. See Panel trasero - Asiento de la 2.ª fila - Centro/20 (5 plazas) (Desinstalación y sustitución).
  19. Install the LH 2nd row seat toe kick cover. See Cubierta - Zona de los pies - Asiento de la 2.ª fila - Lado izquierdo (7 plazas) (Desinstalación y sustitución).
  20. Install the LH 2nd row seat back panel. See Panel trasero - Asiento de la 2.ª fila - Lado izquierdo (Desinstalación y sustitución).
  21. Install the LH 2nd row seat assembly. See Conjunto de asiento - 2.ª fila - Lado izquierdo (7 plazas) (Desinstalación y sustitución).