2026-09-08

Basic Vehicle Inspection (Inspection)

Código de corrección 00030700 FRT 0.90 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT asociado reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver prácticas de trabajo seguras.

  • 2026-06-18: Released new procedure.
Nota
Este procedimiento detalla cómo realizar la inspección básica del vehículo. Cumplimente el formulario SC-26-00-006 mientras realiza este procedimiento.

Desinstalar

  1. Open all doors from the exterior. Verify that the door operates normally and does not do any of the following:
    • Collide with the body or brightwork
    • Produce unusual noises such as creaks, groans, or clicks
    • Pause or fail to fully open
  2. Function check all windows from the LH front switch. Document any abnormal operation or noises.
  3. Function check exterior lights. Verify that the following lights operate normally:
    • Headlights (LH and RH)
    • Fog lights (LH and RH)
    • Taillights (LH and RH)
    • Center high mount stopping light (third brake light)
    • Reverse lights (LH and RH)
    • Side repeaters (LH and RH)
    • Front turn signals (LH and RH)
    • Rear turn signals (LH and RH)
  4. Close the door and hood, then function check the windshield wipers and spray jets. Verify the following:
    • The wipers and jets function
    • The wipers move in a full range of motion
    • The wipers move at all speeds
    • The wipers do not interfere with other components
    • The wipers do not produce abnormal noises such as creaks, groans, and clicks
    • The wipers do not pause
  5. Honk the horn. Verify that both high- and low-tone horns produce sound.
  6. Open the hood.
  7. Remove the rear apron
    Nota
    14x clips
  8. Visually inspect the brake fluid level.
  9. Visually inspect the coolant level. Ensure that the fluid level is at the Max line. Top off as necessary.
  10. Remove the front aeroshield. See Panel - Deflector aerodinámico - Delantero (Paquete estructural) (Desinstalación y sustitución) or Panel - Deflector aerodinámico - Delantero (Sin paquete estructural)(Desinstalación y sustitución).
  11. Install the LH and RH suspension covers. See Cubierta - Suspensión trasera - Lado izquierdo (Desinstalación y sustitución).
  12. Remove the rear aeroshield. See Panel - Deflector aerodinámico - Trasero (Desinstalación y sustitución).
  13. Check tire pressures and adjust to specification as necessary. Inspect tires and wheels for damage or deformities.
    Nota
    Refer to the "Tire and Loading Information" label located on the driver side B-pillar.
  14. Record outer, center, and inner tread depths for all tires.
    Aviso
    Measure the circumferential tire grooves only. Do not place the tire tread gauge probe on the molded treadwear indicators. Recommend replacement if tread depth is 4/32in (3mm) or less.
    Nota
  15. Inspect all brake pads.
    Nota
    Recommend replacement if 2mm or less. Check both inboard and outboard pads
  16. Inspect all brake rotors for excessive wear or rust. See Frenos for minimum specs.
  17. Perform visual inspection of all brake pipes and hoses
    Nota
    Pay special attention to brake junction points
  18. Inspect the front and rear vehicle underside components.
    Nota
    Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
  19. Inspect the underside of vehicle for fluid leaks.
  20. Inspect the steering components.
    Nota
    Check steering gear joints and electrical connections. Verify components are not bent or damaged
  21. Visually inspect the HV battery enclosure.
    Nota
    Check for any dents, scrapes, or other damage
  22. Inspect the front suspension components
    Nota
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  23. Inspect the rear suspension components
    Nota
    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
  24. Install the rear aeroshield. See Panel - Deflector aerodinámico - Trasero (Desinstalación y sustitución).
  25. Install the LH and RH suspension covers. See Cubierta - Suspensión trasera - Lado izquierdo (Desinstalación y sustitución).
  26. Install the front aeroshield. See Panel - Deflector aerodinámico - Delantero (Paquete estructural) (Desinstalación y sustitución) or Panel - Deflector aerodinámico - Delantero (Sin paquete estructural)(Desinstalación y sustitución).
  27. Lower the vehicle fully.
    Nota
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  28. Remove the vehicle from the lift.
    Nota
    Lower the rack arms fully and remove them from under vehicle.
  29. Fill the washer reservoir with fluid.
  30. Install the rear apron
    Nota
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  31. Close the hood.
  32. Perform a road test.
    1. Perform a series of ABS-active stops and ensure proper brake pedal feel and performance.
      Nota
      The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present.
    2. Check the vehicle alignment.
      Nota
      Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension. On a flat road, at 35 mph (56 kph), the vehicle should not pull in either direction.