17/06/2024 14:33:25

Fusible - Bomba de calor - Batería de alta tensión (Paquete estructural) (Desinstalación y sustitución)

Código de corrección 16304012 1.80 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento es PRELIMINAR, aunque ya ha sido validado. Es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.

Retirar

  1. Open all the doors and lower all the windows.
  2. Place the vehicle into Service Mode. See Modo de servicio.
  3. Remove the ancillary bay cover. See Cubierta - Compartimento auxiliar (Paquete estructural) (Desinstalación y sustitución).
  4. Retire el dispositivo pirotécnico de desconexión de la batería. Consulte Dispositivo pirotécnico de desconexión de la batería (Paquete estructural) (desinstalación y sustitución).
  5. Release the tabs that secure the 63A fuse cover to the vehicle, and then remove the cover from the assembly.
  6. Remove and discard the nuts (x2) that attach the 63A fuse to the ancillary bay, and then remove the fuse from the ancillary bay.
    2.5 Nm (1.8 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 8 mm

Instalar

  1. Position the 63A fuse into the ancillary bay, and then install new nuts (x2) that attach the fuse to the ancillary bay.
    2.5 Nm (1.8 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso de 8 mm
  2. Use a Hioki resistance meter to measure the resistance between the 63A fuse and the terminal.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The maximum acceptable resistance is 0.105 mΩ (105 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again
  3. Use a Hioki resistance meter to measure the resistance between the 63A fuse and the auxiliary jumper busbar.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The maximum acceptable resistance is 0.105 mΩ (105 μΩ). There is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again
  4. Install the 63A fuse cover.
  5. Mida la tensión en los puntos de montaje del dispositivo pirotécnico de desconexión de la batería y, a continuación, instale el dispositivo pirotécnico de desconexión de la batería. Consulte Dispositivo pirotécnico de desconexión de la batería (Paquete estructural) (desinstalación y sustitución).
  6. Install the ancillary bay cover. See Cubierta - Compartimento auxiliar (Paquete estructural) (Desinstalación y sustitución).
  7. Exit Service Mode. See Modo de servicio.
  8. Remove the vehicle from the lift. See Elevación del vehículo - Elevador de 2 columnas.
  9. Raise all the windows and close all the doors.