01/03/2023 11:39:25

Moqueta - Delantera - Lado izquierdo (Paquete estructural) (Desinstalación y sustitución)

Código de corrección 15301132 0.30 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Los bordes de la base del asiento están afilados y pueden provocar lesiones personales. Utilice guantes resistentes a los cortes cuando desmonte el asiento del vehículo y cuando realice procedimientos que impliquen trabajar en la base del asiento o cerca de ella.

Retirar

  1. Remove the LH mid A-pillar trim. See Guarnecido - Pilar A - Central - Lado izquierdo (Desinstalación y sustitución).
  2. Remove the LH lower A-pillar trim. See Guarnecido - Pilar A - Inferior - Lado izquierdo (Desinstalación y sustitución).
  3. Remove the LH center console side panel. See Panel lateral - Consola central - Lado izquierdo (Desinstalación y sustitución).
  4. Remove screw and clips (x2) that attach the driver footwell cover to the instrument panel.
    2.5 Nm (1.8 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T20
  5. Disconnect the connectors (x2), and then release the tabs (x3) to remove the driver footwell cover from the vehicle.
  6. Move the LH front seat fully forward.
  7. Remove and discard the bolts (x2) that attach the rear of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx Plus T45
    • Carraca estándar de cabezal flexible de 3/8 pulg.
    • Llave dinamométrica de cabezal flexible de 3/8 pulg. (solo instalación)
  8. Move the seat fully rearward.
  9. Remove and discard the bolts (x2) that attach the front of the 1st row LH seat to the body.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Use only the Torx Plus T45 bit to remove the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx Plus T45
    • Carraca estándar de cabezal flexible de 3/8 pulg.
    • Llave dinamométrica de cabezal flexible de 3/8 pulg. (solo instalación)
  10. Position the LH front seat up and carefully lean it backwards.
  11. Release the push clips (x2) and vertical clip that attach the LH front carpet to the cabin support.
    Consejo: Insert a clip pry tool on the outboard side of the clip, and then rotate to the right to release one side of clip. Move the clip pry tool inboard of clip and rotate to left to fully release the carpet clip from cabin support.
  12. Release the clips (x4) that attach the LH front carpet underneath the seat.
    Figura 1. Seat removed for clarity
  13. Release the harness clip and harness, release all edges, and then remove the LH front carpet from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Take note of the short edge under the center console.

Instalar

  1. Position the LH front carpet into the vehicle, and then secure the harness clip and harness and all edges.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Tuck the short edge underneath the center console.
  2. Install the clips (x4) that attach the LH front carpet underneath the seat.
    Figura 2. Seat removed for clarity
  3. Install the vertical clip and push clips (x2) that attach the LH front carpet to the cabin support.
    Consejo: Secure the vertical clip into place first.
  4. Position the LH front seat down and carefully tilt it forwards.
  5. 33.5 Nm (24.7 lbs-ft)
    Coloque los pernos nuevos (2 uds.) que fijan la parte delantera del asiento izquierdo de la 1.ª fila a la carrocería.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx Plus T45
    • Carraca estándar de cabezal flexible de 3/8 pulg.
    • Llave dinamométrica de cabezal flexible de 3/8 pulg. (solo instalación)
  6. Move the LH front seat fully forward.
  7. 33.5 Nm (24.7 lbs-ft)
    Coloque los pernos nuevos (2 uds.) que fijan la parte trasera del asiento izquierdo de la 1.ª fila a la carrocería.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Use only the Torx Plus T45 bit to install the seat bolts.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx Plus T45
    • Carraca estándar de cabezal flexible de 3/8 pulg.
    • Llave dinamométrica de cabezal flexible de 3/8 pulg. (solo instalación)
  8. Move the LH front seat to the original position.
  9. Position the driver footwell cover into the vehicle, and then connect the connectors (x2) and then secure the tabs (x3).
  10. Install screw and clips (x2) that attach the driver footwell cover to the instrument panel.
    2.5 Nm (1.8 lbs-ft)
    Consejo: Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T20
  11. Install the LH center console side panel. See Panel lateral - Consola central - Lado izquierdo (Desinstalación y sustitución).
  12. Install the LH lower A-pillar trim. See Guarnecido - Pilar A - Inferior - Lado izquierdo (Desinstalación y sustitución).
  13. Install the LH mid A-pillar trim. See Guarnecido - Pilar A - Central - Lado izquierdo (Desinstalación y sustitución).
  14. Close the LH front door.