2026-11-03

Rim - Steering Wheel (Remove and Replace)

Código de corrección 32051102 0.30 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT asociado reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver prácticas de trabajo seguras.

  • 2026-11-03: Updated the specification of the bolts (x4) that attach the bright surround to the steering wheel.
  • 2026-08-10: Added batch information about the bolts (x4) that attach the bright surround to the steering wheel.
  • 2026-01-15: Added steps about the steering wheel ground connection screw and the airbag retaining spring.

Especificaciones de apriete

Table 1. Especificaciones de apriete: Rim - Steering Wheel (Remove and Replace)
Descripción Valor de apriete Herramientas recomendadas Reutilizar/Sustituir Notas
Steering wheel ground connection bolt
1.8 Nm (1.3 lbs-ft)
  • PH1 Stubby Phillips Screwdriver
  • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
 Reutilizar
Bolts (x4) that attach the bright surround to the steering wheel
2.5 Nm (1.8 lbs-ft)
1.8 Nm (1.3 lbs-ft)
  • Torx T25 bit
  • PH1 Stubby Phillips Screwdriver
 Reutilizar

T25 bolts: 2.5 Nm

PH1 bolts: 1.8 Nm
Bolt that attaches the steering wheel to the steering column
80 Nm (59.0 lbs-ft)
  • Vaso de 10 mm
Sustitución 1036655-00-A

Retirar

  1. Disconnect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).
  2. Remove the driver airbag. See Airbag - Conductor (Desinstalación y sustitución).
  3. Disconnect the steering wheel electrical wiring harness connector.
  4. Disconnect the steering wheel heating element connector.
  5. Remove the steering wheel ground connection bolt.
    Tip
    Use of the following tool(s) is recommended:
    • PH1 Stubby Phillips Screwdriver
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
  6. Remove the bolts (x4) that attach the bright surround to the steering wheel, and then release the bright surround and switches assembly from the steering wheel.
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Pry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around. Do not remove it now. Wait until the steering wheel is removed.
    Tip
    Use of the following tool(s) is recommended:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  7. Remove and discard the bolt that attaches the steering wheel to the steering column.
    Tip
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  8. If the new steering wheel rim comes without an airbag retention wire: Squeeze the wire towards the middle and remove the airbag retention wire upwards for reuse.
  9. Remove the steering wheel from the steering column.
  10. Remove steering wheel wiring harness clip.
    Note
    This clip must be easily removable from the back side after the steering wheel is removed, otherwise, it can easily become damaged.

Instalar

  1. Align the keyed parts of steering wheel and column.
  2. Install a new bolt that attaches the steering wheel to the steering column.
    80 Nm (59.0 lbs-ft)
    Tip
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  3. If the new steering wheel rim comes without an airbag retention wire, install the wire removed from the old rim to the new rim.
  4. Install the bolts (x4) that attach the bright surround to the steering wheel.
    2.5 Nm (1.8 lbs-ft)
    1.8 Nm (1.3 lbs-ft)
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Torque the T25 bolts to 2.5 Nm; torque the PH1 bolts to 1.8 Nm.
    Tip
    Se recomienda utilizar las siguientes herramientas:
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  5. Install steering wheel ground connection bolt.
    1.8 Nm (1.3 lbs-ft)
    Tip
    Se recomienda utilizar las siguientes herramientas:
    • PH1 Stubby Phillips Screwdriver
    • Torque wrench 1/4" hexagon (0.2Nm-4Nm)
  6. Connect the steering wheel heating element connector.
  7. Connect the steering wheel electrical wiring harness connector.
  8. Install the driver airbag. See Airbag - Conductor (Desinstalación y sustitución).
  9. Connect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión).