09/02/2024 15:06:33

Pinza de freno - Parte trasera - Par (Desinstalación y sustitución)

33010522 0.84 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
PRECAUCIÓN
El líquido de frenos disuelve la pintura. Tenga trapos limpios y abundante agua cerca para limpiar el líquido de frenos en caso de que se derrame sobre superficies pintadas.
Informational PurposesAn informational icon, calling your attention
Nota
Deseche el líquido de frenos usado de acuerdo con las normas medioambientales locales.
Informational PurposesAn informational icon, calling your attention
Nota
This procedure is applicable to both base and sport type brake calipers.
  1. Prepare the vehicle for lifting, but do not lift it at this time. See Elevación del vehículo - Elevador de 2 columnas.
  2. Open the LH front door and lower the window.
  3. Enable Service Model via the touchscreen. See Modo de servicio.
  4. Unlock the vehicle gateway. See Puerta de enlace (Desbloquear).
  5. Put the EPB in Service Mode: on the touchscreen, touch Chassis > Brakes > EPB Service Mode, from the drop down menus, select Both and Start, and then touch Run.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    The vehicle may roll freely.
  6. Remove LH and RH rear wheels. See Conjunto de rueda (Desinstalación e instalación).
  7. Disconnect the LH rear brake caliper connector.
  8. Remove the bolt that attaches the LH rear brake caliper harness bracket.
  9. Position an oil drain container under LH rear brake hose area.
  10. Remove the tube nut that attaches the LH rear brake line to the LH rear brake hose.
  11. Remove and discard the LH rear jounce hose clip.
  12. Position the oil drain container under the LH rear brake caliper area.
  13. Remove the bolt that attaches the LH rear brake hose to the LH rear brake caliper.
  14. Remove and discard the bolts (x2) that attach the LH rear brake caliper bracket to the knuckle, and then remove the brake caliper from the vehicle.
  15. Install new bolts (x2) that attach the LH rear brake caliper bracket onto the knuckle (torque 83 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Mark the bolts with a paint pen after torquing.
  16. Install a new bolt and new copper washers (x2) that attach the LH rear brake hose to the LH rear brake caliper (torque 42 Nm).
    Informational PurposesAn informational icon, calling your attention
    Nota
    Mark the bolt with a paint pen after torquing.
  17. Install a new LH rear jounce hose clip to attach the hose to the body.
  18. Position the oil drain container under the LH rear brake hose area.
  19. Install the LH rear brake line tube nut to the LH rear brake hose (torque 16 Nm).
  20. Install the nut that attaches the LH rear brake caliper harness bracket (torque 5 Nm).
  21. Connect the LH rear brake caliper connector.
  22. Repeat steps 7 through 21 on the RH side of the vehicle.
  23. Bleed the LH and RH brake calipers. See Purga del líquido de frenos - Una pinza.
  24. Put the vehicle into park.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure that parking brakes are engaged. Putting the vehicle into Park also disables EPB Service Mode.
  25. Perform a road test and burnish the brakes. See Pastillas de freno - Pulido.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure proper brake pedal feel and performance. Add correction code 33013000 as a separate activity to the SV.