Código de corrección 13084212 0.66 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

1. Open RH front and rear doors
2. Lower all four windows
3. Move LH front seat forward
4. Move RH front seat forward
5. Partially remove LH rear door seal

   

6. Remove LH 7s Lower C-Pillar Trim
   Nota

   8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim

   

   

7. Fold 60 seat into down position

   

   

8. Disconnect logic connector at LH seat frame
   Nota

   1x connector

   

9. Move 60 seat forward using towel bar
   Nota

   With one hand on towel bar pull up and slide the seat forward with your other hand

   

   

10. Remove 60 seat rear outboard track fastener
    Nota

    1x patch bolt, 11mm, 37 Nm, Discard after removal

    

11. Remove 60 seat rear inboard track fasteners
    Nota

    2x patch bolts, 11mm, 37 Nm, Discard after removal

    

12. Move 60 seat fully rearward using towel bar
    Nota

    With one hand on towel bar pull up and slide the seat forward with your other hand

    

13. Remove 60 seat outboard track cover
    Nota

    1x clip, Slide covers forward to release from 60 seat tracks

    

    

    

14. Remove center track cover from 2nd row seats
    Nota

    2x clips, Slide covers forward to release from 2nd row seat tracks

    

    

    

15. Release cabin carpet from 60 seat
    Nota

    Pull cabin carpet towards front of vehicle

    

    

16. Remove 60 seat front inboard track fasteners
    Nota

    1x bolts, 11mm, 37 Nm, Discard after removal

    

17. Remove 60 seat front outboard track fasteners
    Nota

    1x bolts, 11mm, 37 Nm, Discard after removal

    

18. Remove 2nd row 60 seat assembly from vehicle
    Nota

    Recommend assistance

    

    

19. Remove front push clip from 60 outer sideshield assembly
    Nota

    1x clip, Use pick to remove the push clip from the bottom side of the outboard cover

    

    

20. Remove 60 outer sideshield assembly
    Nota

    1x clip 1x connector, Remove outer sideshield assembly by pulling outwards and up at the front portion of the trim, Unclip remaining clip and unplug the connection

    

    

21. Remove 60 seat toe kick cover
    Nota

    7x clips, Pry up on LH side of 60 toe kick cover to release clips, Repeat on RH side to fully remove

    

    

22. Release clips and remove inboard outer trim from 60 seat
    Nota

    3x clips, Use trim tool to unclip 3x clips and remove inboard outer trim towards rear of the vehicle

    

    

23. Remove 60 seatback panel
    Nota

    9x clips, 2x hooks, Release clips starting at the top of backpanel working your way down the lower backpanel, pull 60 backpanel towards front of vehicle to remove

    

    

24. Remove 2nd row center seat switch
    Nota

    1x connector, 2x clips, Using plastic trim tool pry the top of the switch away from 20 backpanel to ease removal

    

    

    

25. Remove center backpanel from center seatback
    Nota

    5x clips, 2 hooks, Lift up at the lower 20 backpanel and then slide forward to release

    

    

    

26. Release 60 seat harness connectors and clip from seat from seat frame
    Nota

    1x clip, 7x connectors

    

    

27. Disconnect seat cables from easy entry actuators on 60 seat
    Nota

    4x clips

    

28. Remove push clips for 60 bottom seat pan
    Nota

    2x clips, Remove push clips from front of seat pan

    

29. Remove center seatback lumbar bun fastener
    Nota

    1x screw, T20, 1.5 Nm

    

    

30. Remove center seatback lumbar bun
    Nota

    2x clips, Pull bolster outwards to release

    

31. Remove center seatback pivot clamps
    Nota

    2x bolts, T40, 22 Nm, Once fasteners are removed slide pivot clamp towards the center of center seatback and pull each outwards to remove

    

    

    

    

32. Remove center seatback from 60 seat frame
    Nota

    Remove center seatback by lifting upwards

    

33. Manually release the center seatback latch
    Nota

    Use small screwdriver to manipulate the center seatback latch to release

    

    

34. Remove fasteners securing 60 seat pan to seat frame
    Nota

    4x fastener, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Remove remaining bolts attaching seat pan to seat frame

    

    

    

35. Remove headrest from 60 seat assembly
    Nota

    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening, Lift up while engaged

    

    

36. Remove headrest guides from 60 seat
    Nota

    Pull back on lower portion of the headrest guide to release tab while also applying upward force to remove headrest guides

    

    

37. Remove 60 seatback
    Nota

    4x clips, Release clips securing 60 seatback and lift upwards

    

38. Remove 60 seat bottom
    Nota

    Remove seat bottom by lifting the rear first and removing it towards front of the seat

    

39. Remove push clip from trim
    Nota

    1x clip, Remove trim clip from cover

    

40. Remove center inner cover
    Nota

    2x clips, Pry center inner cover back to disengage clips, Remove by lifting up while pulling back

    

    

41. Remove 60 B-Cover I/B Inner

    

42. Install 60 B-Cover I/B Inner trim

    

43. Install center inner cover
    Nota

    2x clips, Install inner cover ensuring the clips seat to outer cover

    

44. Install push clip to trim
    Nota

    1x clip

    

45. Place 60 seat pan onto seat frame
    Nota

    Reinstall seat bottom onto seat frame by starting at the rear of the seat

    

46. Secure 60 seat bottom to seat frame
    Nota

    4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame

    

    

    

47. Install headrest guides into 60 seat assembly
    Nota

    Install headrest guides by pressing downwards until lower tab is seated

    

48. Install 60 seat back into place
    Nota

    4x clips, Slide seat back into place making sure the bottom retainers slide into place, Reinstall push clips to secure seat back

    

49. Install headrest onto 60 seat assembly
    Nota

    Push down to secure

    

50. Install center seatback pivot clamps
    Nota

    2x bolts, T40, 22 Nm, Insert pivot clamp at center of center frame and slide outwards to install fasteners, When replacing pivot clamps they must be replaced in pairs

    

    

    

51. Install center seatback lumbar bun fastener
    Nota

    1x screw, T20, 1.5 Nm

    

    

52. Plug in connector and install trim to 60 seat
    Nota

    1x connector, 1x clip, Plug in connector and install trim by hooking the front into place and seat clip at rear of trim.

    

    

53. Install push clip at front of outer 60 sideshield assembly
    Nota

    1x clip, Install push clip at front bottom side of the trim

    

    

54. Install inboard outer trim to 60 seat
    Nota

    Clips 3x, Install inboard outer trim and reseat 3x clips

    

55. Insert backpanel hooks into center seat back assembly
    Nota

    2x hooks, Engage hooks and slide rearward into position, Early production have 4x hooks

    

    

56. Install center backpanel onto seat back
    Nota

    5x clips

    

57. Install 2nd row center seat switch
    Nota

    1x connector, 2x clips

    

    

    

58. Install 60 toe kick cover
    Nota

    7x clips

    

    

59. Install LH seatback onto 60 seat assembly
    Nota

    9x clips, 4 hooks, Attach hooks onto frame rail, Work upwards and fasten all the clips

    

    

    

60. Connect logic connector at LH 60 seat frame
    Nota

    1x connector

    

61. Install fasteners securing 60 seat frame to body
    Nota

    5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front

    

    

    

    

62. Secure cabin carpet to 60 seat
    Nota

    Strap velcro on

    

    

63. Fold the 60 seat into vertical position
    Nota

    Remove seat back protection if necessary

    

64. Install 60 seat outboard track cover
    Nota

    1x clip

    

    

    

65. Install 60 seat outboard track cover
    Nota

    1x clip

    

    

    

66. Install LH 7s Lower C-Pillar Trim
    Nota

    8x clips, Rear edge is mated with groove in trunk side trim, Release clips at the front of LH rear sill trim working your way back towards rear of sill trim

    

    

67. Reseat LH rear door seal
    Nota

    Seat pillar and sill trim tabs underneath seal

    

68. Move RH front seat to original position
69. Raise all four windows
70. Close all four doors
    Nota

    If 12V is powered up, Unlatch rear doors before closing