Prueba de fugas de aire del compartimento auxiliar (paquete estructural)
Código de corrección
16100420 0.55
NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.
NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com.
NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.
- 2025-09-05: Cleaned up procedure and removed redundant illustration.
Procedure
- Open all doors and lower the windows.
- Open the hood.
-
Remove the rear apron.
Nota14x clips
- Remove the bolt that attaches the underhood storage unit to the washer fluid reservoir neck.
- Remove the HEPA filter assembly. See Conjunto - Filtro - HEPA (Desinstalación y sustitución)
- Move LH front seat forward
- Move RH front seat forward
- Disconnect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión)
- Perform the vehicle HV disablement procedure. See Procedimiento de desactivación de la alta tensión del vehículo (Paquete estructural)
- Remove the push clips at the left and right wheel house liner to mid aero shield.
- Lower the vehicle until the tires are touching the floor.
- If present, cut away the insulation that covers the pyro cover.
- Remove and discard the breather from the pyro cover.
- Install the air splitter hose onto the pyro cover.
- Connect the regulator to air supply.
- Turn the right side regulator valve to the open position.
- Set the regulator to 0.3 psi.
-
Open the left side regulator valve to inject air into the ancillary bay.
NotaAllow 30 seconds fill time. Close the right side regulator valve when the pressure reaches 0.3 psi.
- Wait 15 seconds for the pressure to settle.
- Record the value of the starting pressure.
- Wait 30 seconds to test pressure.
-
Record the value of the end pressure.
NotaSubtract ending pressure from starting pressure. If the difference is greater than 0.0484 psi, then inspect the tools and retest. If the difference is still greater than 0.0484 psi, then proceed to the Combined Platter and Ancillary Bay leak down test. If difference is 0.0484 psi or less, then proceed with the current procedure.
- Disconnect air supply from regulator tool
- Install a new breather onto the pyro cover.
- Raise the vehicle.
-
Connect the RDU HV harness to the HV battery.
NotaVerify lever is in the upright and open position. Carefully seat the connector and allow the lever to engage. Fully secure the lever and make sure that the red tab is locked.
-
Install the mid aero shield.
Nota11x bolts, 10mm, 5 Nm. Model Y Structural Pack will have one less bolt and one extra clip.
- Install the push clips (x2) at the left and right wheel house liner to the mid aero shield.
- Connect LV power. See Alimentación de 12 V/baja tensión (Desconexión y conexión)
- Install the HEPA filter assembly. See Conjunto - Filtro - HEPA (Desinstalación y sustitución)
-
Attach the washer tank neck onto the washer tank.
Nota1x O-ring. Make sure that the washer hose is properly routed.
-
Install the bolt that attaches the underhood storage unit to the washer fluid reservoir neck.5 Nm (3.7 lbs-ft)
- Install the rear apron.
- Close the hood.
-
Install the 2nd row seat cushion.
Nota1x connector. Slide the rear cushion rearward, then align foam with the seat rail. Make sure that the cushion is fully seated with push & pull test.
- Move LH and RH front seats to their original position.