18/12/2023 12:59:47

Barra colectora - Salida - Positiva - Carga rápida - Batería de alta tensión (Paquete estructural) (Desinstalación y sustitución)

Código de corrección 16307202 1.92 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga.NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Warning IconA warning icon, calling your attention to a possibly risky situation
Aviso
Este procedimiento es PRELIMINAR, aunque ya ha sido validado. Es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos. Envíe sus correcciones y comentarios a ServiceDevelopment@teslamotors.com.
  1. Open all four doors
  2. Lower all four windows
  3. Place vehicle in service mode with touchscreen
    Informational PurposesAn informational icon, calling your attention
    Nota
    Hold Tesla T icon at top of center display for four seconds and then type "service" into dialog box
  4. Remove the ancillary bay cover. See Cubierta - Compartimento auxiliar (Paquete estructural) (Desinstalación y sustitución).
  5. Retire el dispositivo pirotécnico de desconexión de la batería. Consulte Dispositivo pirotécnico de desconexión de la batería (Paquete estructural) (desinstalación y sustitución).
  6. Disconnect fast charge contactor
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Push on both side of connector to release tabs and pull upward
  7. Remove bolt securing AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  8. Remove bolt securing AC filter harness positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  9. Release AC filter harness from tray
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips
  10. Remove FC contactor cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x securing tabs
  11. Remove bolts securing FC positive outlet jumper
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  12. Remove FC positive outlet jumper from ancillary bay
  13. Position FC positive outlet jumper onto ancillary bay
  14. Install bolts securing FC positive outlet jumper
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x bolts, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Discard after removal
  15. Perform Hioki measurement at the joint from FC positive outlet jumper busbar to DC positive link busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1 HV joint, 60µΩ or less
  16. Install FC contactor cover
    Informational PurposesAn informational icon, calling your attention
    Nota
    3x securing tabs
  17. Install bolt securing AC filter harness positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Install new bolt
  18. Install bolt securing AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x bolt, 13mm, 15 Nm, Minus 180 degrees, 5 Nm + 60 degrees, Install new bolt
  19. Perform Hioki impedance measurement at joint from AC filter harness to positive DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x HV joint, 150µΩ or less
  20. Perform Hioki impedance measurement at joint from AC filter harness to negative DC inlet busbar
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x HV joint, 150µΩ or less
  21. Secure AC filter harness onto tray
    Informational PurposesAn informational icon, calling your attention
    Nota
    2x clips
  22. Connect fast charge contactor
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x connector, Push on both side of connector to release tabs and pull upward
  23. Mida la tensión en los puntos de montaje del dispositivo pirotécnico de desconexión de la batería y, a continuación, instale el dispositivo pirotécnico de desconexión de la batería. Consulte Dispositivo pirotécnico de desconexión de la batería (Paquete estructural) (desinstalación y sustitución).
  24. Install the ancillary bay cover. See Cubierta - Compartimento auxiliar (Paquete estructural) (Desinstalación y sustitución).
  25. Exit Service Mode through UI
    Informational PurposesAn informational icon, calling your attention
    Nota
    Controls > Service Mode > Exit Service Mode
  26. Raise all four windows
  27. Close all four doors
    Informational PurposesAn informational icon, calling your attention
    Nota
    If 12V is powered up, Unlatch rear doors before closing