2026-03-03

Tie Rod Kit - LH (Remove and Replace)

Código de corrección 32013202 FRT 0.48 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana (FRT) para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a ServiceManualFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

  • 2025-12-16: Released new procedure.

Desmontar

  1. Raise and support the vehicle. See Elevación del vehículo - Elevador de 2 columnas
  2. Open LH front door
  3. Lower LH front window
  4. Remove the LH front wheel arch liner. See
  5. Remove and discard the nut that secures the LH front tie rod end to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  6. Remove the LH front tie rod end from the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the rotor back and forth for easier removal.
  7. Remove and discard the large clamp from the bellows.
  8. Remove the seal clip from the bellows.
  9. Slide the bellows toward the LH outer tie rod end to access the ball joint.
  10. Remove the LH tie rod assembly from the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)

Instalar

  1. Turn the jam nut on the new tie rod to adjust the length and match the old tie rod before installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Count the threads on the removed tie rod, then adjust to the same count on the new one. This will make alignment adjustment easier.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of the following tool(s) is recommended:
    • 21 mm 12pt combination wrench
    • 14 mm 12pt combination wrench
    • Extension
  2. Install the LH inner tie rod assembly onto the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)
  3. Slide the bellows into the clamping position.
  4. Secure the large bellows clamp onto the bellows.
  5. Secure the bellows seal clip onto the bellows.
  6. Position the LH front tie rod end to the LH front knuckle.
  7. Install a new nyloc nut to secure the LH tie rod end to the LH front knuckle
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  8. Remove the LH front wheel arch liner. See
  9. Remove the vehicle from the lift. See Elevación del vehículo - Elevador de 2 columnas
  10. Raise the windows and close the doors.
  11. Review the wheel alignment requirements and add correction code as needed. See Requisito de alineación - Suspensión