2026-04-17

Capteur – ultrasonique – porte arrière – gauche (retrait et remplacement) (Manual Method)

Code de correction 11334312 0.66 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. NOTE : Consultez Protection individuelle pour veiller à porter l’ÉPI approprié lorsque vous effectuez la procédureci-dessous.

  1. 2026-04-02: Released new procedure. Existing procedure split due to tooling availability.
Informational PurposesAn informational icon, calling your attention
Remarque
If the ultrasonic sensor install tool (2039351-00-A) is available in your region, see Capteur – ultrasonique – porte arrière – gauche (retrait et remplacement) (Tool Method).

Retirer

  1. Open the LH front door.
  2. Lower the LH front window.
  3. Lower the LH rear window.
  4. Open the LH falcon wing door.
  5. Remove the LH rear door trim panel. See Panneau - garniture de portière - arrière - gauche (retirez et remplacez).
  6. Disconnect LV power. See Alimentation 12 BT (déconnecter et connecter).
  7. Remove the LH rear door closeout panel. See Panneau de fermeture - porte - arrière - gauche (retirez et remplacez).
  8. Remove the cap, spring and spacer from the LH rear door ultrasonic sensor.
  9. Release the LH rear door ultrasonic sensor locking clip, and then disconnect the sensor connector.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Outil de levier avec pince
  10. Remove the LH rear door ultrasonic sensor from the vehicle and discard it.

Installer

Warning IconA warning icon, calling your attention to a possibly risky situation
ATTENTION
The ultrasonic sensor is a one time use component. If the ultrasonic sensor is removed, it must be discarded and a new ultrasonic sensor must be installed.
  1. Use IPA wipes to clean the LH rear door ultrasonic sensor mounting area. Allow 1 minute dry time.
  2. Cut hair pins (x4) at the pictured location.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Cutting pliers
    Figure 1. Hair pin cut location
  3. Install the hair pins (x4) onto the ultrasonic sensor carrier with the bumps facing outward.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The sensor should not be installed at this time. The image is for reference only.
  4. Use an infrared (IR) thermometer to read the temperature of the LH rear door ultrasonic sensor mounting area on the door panel prior to sensor installation. The door panel must be 25º C or warmer. Use a heat gun to warm the sensor mounting area until the required temperature range is achieved.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Heat gun
    • IR thermometer
  5. Peel off the adhesive from the new LH rear door ultrasonic sensor.
  6. Use an infrared (IR) thermometer to read the temperature of the LH rear door ultrasonic sensor prior to installation. The sensor must be 70ºC (158ºF) Use a heat gun to warm the sensor until the required temperature is achieved.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Heat gun
    • IR thermometer
  7. Install the LH rear door ultrasonic sensor on the door panel.
  8. Attach the 22 mm tip to the force gauge, and then apply a force of 65 N for 30 seconds to fully press the LH rear door ultrasonic sensor onto the door.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Nous recommandons l’utilisation des outils suivants :
    • Force gauge - 1080978-00-B
  9. Remove the hair pins from the ultrasonic sensor carrier.
  10. Install the cap, spring and spacer on the LH rear door ultrasonic sensor.
  11. Connect the LH rear door ultrasonic sensor, and then engage the locking clip.
  12. Install the LH rear door closeout panel. See Panneau de fermeture - porte - arrière - gauche (retirez et remplacez).
  13. Install the LH rear door trim panel. See Panneau - garniture de portière - arrière - gauche (retirez et remplacez).
  14. Connect LV power. See Alimentation 12 BT (déconnecter et connecter).
  15. Calibrate the LH and RH falcon wing doors.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If the "Calibration Needed" message appears on the vehicle touchscreen, touch and hold Calibrate to calibrate the rear doors.
  16. Raise the LH rear window.
  17. Raise the LH front window.
  18. Close the LH front door.