2024-01-15

Carte de connectivité - Ordinateur de bord (retrait et remplacement)

Code de correction 21152902 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
  1. Open LH front door
  2. Lower LH and RH front windows
  3. Open RH front door
  4. Move RH front seat backward
  5. Open hood
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Via center display > Controls > Frunk Open
  6. Power off vehicle via center display
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Controls > Safety & Security > Power Off
  7. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x datums
  8. Disconnect LV battery connector and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL
  9. Remove RH front floor mat
  10. Remove RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x magnets, 1x connector, 4x datums
  11. Remove RH console side carpet
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x datums
  12. Remove RH front door sill trim panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, 3x datums
  13. Remove RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  14. Remove RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
  15. Remove RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  16. Fold RH front cabin carpet aside for access
  17. Release harness from RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  18. Release RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm
  19. Remove RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Fold RH primary support carpet up, Rotate RH footrest panel out of vehicle
  20. Release connection at LH side of AP motherboard
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Release antenna connector that crosses in front of car computer cover (Brown connector), Release lock on connector before removal
  21. Release connector to connectivity module
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Move release lock rearward before removal
  22. Put on ESD wrist strap and connect to vehicle ground
  23. Remove the car computer top cover fasteners
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x screws, T10, 1.4 Nm, Discard after removal, Power tools recommend to reduce time required
  24. Remove car computer cover
  25. Remove the connectivity board mounting screws
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x screws, T10, 0.7 Nm, Discard after removal
  26. Slide the connectivity board down to separate connector and remove
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Ensure full disengagement of connectivity board before attempting to remove
  27. Slide the connectivity board in to the PCB connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, 1x datum, Align datum with slot in connectivity card and fully engage
  28. Install mounting screws to secure connectivity board
    Informational PurposesAn informational icon, calling your attention
    Remarque
    6x screws, T10, 0.7 Nm, Install new fasteners
  29. Install car computer cover
  30. Install top cover mounting screws
    Informational PurposesAn informational icon, calling your attention
    Remarque
    9x screws, T10, 1.4 Nm, Install new screws
  31. Remove the ESD wrist strap
  32. Install connector to connectivity module
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector, Slide lock underneath connector
  33. Install connection at LH side of AP motherboard
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x connector
  34. Connect First Responder Loop and LV battery connector
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage upper locking tab when fully seated
  35. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    Remarque
    11x clips, 2x datums
  36. Close hood
  37. Install RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Rotate RH footrest panel onto vehicle, Fold RH primary support carpet down
  38. Secure RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm
  39. Secure harness to RH footrest panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x clip
  40. Fold RH main carpet back into place
  41. Install RH footwell cover
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x magnets, 4x datums, 1x connector
  42. Install RH lower A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  43. Install RH mid A-pillar trim
    Informational PurposesAn informational icon, calling your attention
    Remarque
    2x clips, 3x datums, Verify weather seal is seated properly
  44. Install RH IP end cap
    Informational PurposesAn informational icon, calling your attention
    Remarque
    3x clips
  45. Install RH front door sill trim panel
    Informational PurposesAn informational icon, calling your attention
    Remarque
    8x clips, 3x datums
  46. Install RH front floor mat
  47. Move RH front seat to original position
  48. Calibrate RH falcon wing door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Hold the upper B-pillar button in the down position to manually calibrate
  49. Raise RH front window
  50. Close RH front door
  51. Calibrate LH falcon wing door
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Hold the upper B-pillar button in the down position to manually calibrate
  52. Raise LH front window
  53. Close LH front door
  54. Verify BT, WiFi, and LTE are functioning properly