2024-06-20

Phares - réglage (international) (méthode des outils)

Code de correction 17400170 0.18 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. NOTE : Consultez Protection individuelle pour veiller à porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous. REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à ServiceManualFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

  • 2024-06-13: Updated procedure to latest validation.

Adjustment

  1. Entrez dans le mode de réglage des phares :
    1. Sur l’écran tactile du véhicule, touchez Contrôles > Entretien > Ajuster les phares.
    2. Si on vous demande d’étalonner les phares (figure A), poursuivez à la sous-étape c. Si on vous demande d’ajuster les phares (figure B), passez à l’étape 2.
      Figure 1. Figure A
      Figure 2. Figure B
    3. Pour étalonner les phares, suivez les directives sur l’écran tactile. L’étalonnage est terminé lorsque les 4 crochets sont passés du « rouge » au « vert ».
      Informational PurposesAn informational icon, calling your attention
      Remarque
      Pour l’étalonnage, vous pourriez avoir à conduire jusqu’à 2 km (1,24 mi).
      Informational PurposesAn informational icon, calling your attention
      Remarque
      Pour assurer un étalonnage précis :
      • Après avoir activé les ponts d’alimentation, attendez au moins une seconde avant de passer en marche avant.
      • Fermez toutes les portes du véhicule et ne les ouvrez pas lors de la conduite d’étalonnage.
      • Après avoir arrêté le véhicule, attendez au moins une seconde avant d’ouvrir les portes.
      • Ne conduisez pas en marche arrière sur plus de 10 mètres. S’il est inévitable de la faire en raison de la disposition du garage, démarrez l’étalonnage des phares seulement après que le véhicule soit sorti du garage.
    4. Les phares peuvent être ajustés après que l’étalonnage soit terminé. Passez à l’étape suivante.
  2. Set vehicle ride height to "Low".
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using the touchscreen, touch Controls > Suspension > Low.
  3. Activate Jack Mode.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using the touchscreen, touch Controls > Service > Jack Mode.
  4. Open the hood.
  5. Switch on the headlights.
  6. If not yet entered, enter the headlight adjustment mode through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Using the touchscreen, touch Controls > Service > Adjust Headlights.
  7. Position headlight aimer in front of the LH headlight.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Position the headlight aimer at 30 cm (~ 12 in) distance from the surface of headlight lens. Adjust the height as necessary to match the center point of the headlight (81 cm/32 in).
  8. Power on the headlight aimer.
  9. Use the knobs on the base to adjust tester level.
  10. Use the visor/laser to line up the tester perpendicular to the axis between the hood struts.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    If the headlight aimer can move between RH and LH headlights while maintaining the same laser angle projected onto the hood struts, it is set correctly - perpendicular to the car
  11. Regardless of the region, select TEST EC on the headlight aiming tool.
  12. Select Free test.
  13. Select Vehicle, and then use the + or - buttons to set the vehicle type to Tesla X.
  14. Select Headlight, use the + or - buttons to set the Headlight type to EU Asym, and then use the small - button next to the EU Asym field to select TMR.
  15. Select Light, and then use the + or - buttons to set the Light type to Bi-LED.
  16. Select Inclinat., and then use the + or - buttons to set the inclination to 0.0 %.
  17. Select Height, and then adjust to 81 cm using the +/- buttons.
  18. Press OK, and then press OK again to skip the fog light settings.
  19. Select the laser icon and adjust the tester horizontal and vertical position to align with the LH headlight markings.
  20. Turn off the laser guide.
  21. On the headlight tester tool, press the LH TMR button on the left side of the screen, and then press the TMR button at the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
  22. On the vehicle touchscreen, touch Left.
  23. On the steering wheel, use the left scroll wheel to adjust the beam. When adjusted to within specification, the color of the beam indicator on the headlight tester tool will change from red to green.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    There might be a delay between the scroll wheel input and the actual headlight adjustment output.
    Figure 3. Model Y shown, Model X similar
  24. Select the save icon to record results
  25. On the headlight tester tool, press the "Save" button to record the results for the LH headlight.
  26. Move the headlight tester tool to the RH headlight, position the tool ~ 30 cm (~ 12 in) from the front of the RH headlight lens.
  27. Align the tool to the RH headlight (see steps 19 and 20).
  28. On the headlight tester tool, press the RH TMR button on the right side of the screen, and then press the TMR button at the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    The "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
  29. On the vehicle touchscreen, touch Right.
  30. On the steering wheel, use the left scroll wheel to adjust the beam level. When adjusted to within specification, the color of the beam indicator on the headlight tester tool will change from red to green.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    There might be a delay between the scroll wheel input and actual headlight adjustment output.
    Figure 4. Model Y shown, Model X similar
  31. On the headlight tester tool, press the "Save" button to record the results for the RH headlight, and then press "Save" again to view the results for both headlights.
  32. Press the "Print" button to print out the results, if desired.
  33. Close the front trunk.
  34. On the touchscreen, exit the headlight adjustment mode.