2024-06-03

Soulever le véhicule - pont élévateur à 2 poteaux

Code de correction 10000205 0.05 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. NOTE: Consultez Protection individuelle pour vous assurer de porter l’ÉPI approprié lorsque vous effectuez la procédure ci-dessous.

  • 2024-05-29: Added EMEA specific info on offsetting lift pads to provide additional clearance for HV battery removal.
  • 2023-08-16: Added to set air suspension to "Very High" before Jack Mode is enabled.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Cette procédure est une PREMIÈRE VERSION. Bien qu'elle ait été validée, des avertissements et des mises en garde pourraient manquer. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près des systèmes et des composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
Remarque
A vehicle lifting procedure is available for Mobile Service. See Soulever le véhicule - cric de plancher (entretien mobile).

Soulever

Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
Pour réduire les risques de blessures, vous devez porter un équipement approprié pour effectuer cette procédure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Avertissement
N’effectuez jamais de travaux sur un véhicule qui n’est pas convenablement soutenu.
  1. Disconnect the charging cable from the vehicle.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Avertissement
    Do not attach the charging cable to the charge port while the vehicle is on the lift.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    Perform a visual check of the lift according to the equipment operator's manual before using the lift.
  2. Move the lifting arms fully outward.
  3. Move the vehicle to the lift, position the vehicle centrally between the lift posts, and make sure that the steering wheel is in line with the lift posts.
  4. On the vehicle touchscreen, touch Controls > Suspension > Very High to set the air suspension to the "Very High" setting.
  5. On the vehicle touchscreen, touch Controls > Service > Jack Mode to activate Jack Mode.
  6. Position the front and rear lifting arm pads under the vehicle lift points on the HV battery as shown.
    • NA only:
      Informational PurposesAn informational icon, calling your attention
      Remarque
      Some lifting arms extend past the lifting pad and might obstruct separation of the HV battery from the vehicle. In this situation, rotate the lifting pads 90 degrees, so as to provide additional clearance.
      Figure 1. Lifting arm obstructing separation of HV battery from vehicle
      Figure 2. Lifting pad at 90 degrees
    • EMEA only:
      Informational PurposesAn informational icon, calling your attention
      Remarque
      Lifting arms of Beisbarth and AMI lifts may extend past the lifting pad and might obstruct separation of the HV battery from the vehicle. In this situation, position the liftpad with a 1 cm offset to the outside of the vehicle, so as to provide additional clearance.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      Avertissement
      More than 80% of the lift pad must be in contact with the vehicle.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      Avertissement
      The metal center part of the lifting pad (threaded section) must remain completely under the vehicle at al times.
  7. Adjust the lifting arm pads to the optimum height.
  8. Make sure that the hood, liftgate, and all doors are closed, unless necessary for the work to be performed.
  9. Check that the arms are correctly located, and make sure that no part of the vehicle is in danger of contacting the ceiling, tool boxes, or other items in the service area when the vehicle is raised.
  10. Raise the vehicle slightly, and check the following:
    • Make sure all 4 pads are in the correct position.
    • Check the balance of the vehicle.
    • Make sure that the four arms are properly locked and cannot rotate.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    If the procedure requires the hood, liftgate, or doors to be open while the vehicle is raised, closely watch their position as the vehicle is being raised to avoid contact with the lift mechanism, ceiling, or objects hanging from the ceiling.
  11. Raise the vehicle to the necessary service height, and then lower the lift until the safety locks are properly engaged.

Abaisser

  1. Make sure that no tools, equipment, other items, or personnel are under the vehicle or under any open doors.
  2. Disengage any lift safety locks, and fully lower the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Remarque
    Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    ATTENTION
    To avoid injuries, stay clear from the vehicle.
  3. Move the lifting arms fully out from under the vehicle, and lower the lifting pads.
  4. Close any open hood, liftgate, or doors as necessary.
  5. On the vehicle touchscreen, touch Controls > Service > Jack Mode to deactivate Jack Mode.
  6. On the vehicle touchscreen, touch Controls > Suspension and set the air suspension to the previous setting. If not sure, set the air suspension to "Medium".
  7. Remove the vehicle from the lift.