Code de correction 17107702 17107802 0.42 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

1. Open the LH front door.
2. Lower the LH front window.
3. Raise and support the vehicle.

   

   

4. Open the hood.

   

5. Remove the rear underhood apron.

   

   

6. Remove the RH underhood apron.

   

   

   

   

7. Remove the LH underhood apron.

   

   

   

   

8. Remove the front underhood apron.

   

   

9. Remove the underhood storage unit access panel.

   

   

10. Remove the underhood storage unit carpet.

    

    

11. Remove the underhood storage unit from the vehicle.

    

    

12. Disconnect active noise cancellation harness connector from frunk harness
    Remarque

    1x connector, Release locking tab, 1x harness clip, Release clip securing active noise cancellation harness connector onto body

    

    

    

13. Remove the LH front wheel center cap.

    

    

14. Loosen LH front wheel
    Remarque

    5x nuts, 21mm, 175 Nm

    

15. Raise vehicle partially and lower onto locks
    Remarque

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

16. Remove the LH front wheel.

    

17. Release clips securing active noise cancellation harness onto bracket
    Remarque

    2x harness clip

    

    

18. Disconnect active noise cancellation harness connector from sensor and remove harness from vehicle
    Remarque

    1x connect, Release locking tab

    

19. Connect active noise cancellation harness onto sensor
    Remarque

    1x connect, Secure locking tab

    

20. Position active noise cancellation harness into place
    Remarque

    Ensure the harness is routed above the lower links and below the tie rod and halfshaft

    

    

21. Install clips securing active noise cancellation harness onto bracket
    Remarque

    2x harness clip

    

    

22. Install the LH front wheel.

    

23. Lower vehicle until tires are touching ground
    Remarque

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

    

24. Torque the LH front wheel lug nuts.

    

25. Install the LH front wheel center cap.

    

    

26. Connect active noise cancellation harness connector to frunk harness
    Remarque

    1x connector, Secure locking tab, 1x harness clip, Install clip securing active noise cancellation harness connector onto body

    

    

    

27. Install the underhood storage unit.

    

28. Install the underhood storage unit carpet.

    

    

29. Install the underhood storage unit access panel.

    

    

30. Install the front underhood apron.

    

    

31. Install the LH underhood apron.

    

    

    

    

32. Install the RH underhood apron.

    

    

    

    

33. Install the rear underhood apron.

    

    

34. Close the hood.
35. Lower and remove the vehicle from the lift.

    

36. Raise the LH front window.
37. Close the LH front door.