2026-04-30

Trim Cover - Cushion - 2nd Row Seat - RH (7-Seat) (Remove and Replace)

Código de corrección 1308020902 0.84 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Retirar

  1. Open all four doors.
  2. Lower all four windows.
  3. Move RH front seat forward.
  4. Position RH seat into easy entry mode.
  5. Partially remove RH rear door seal.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pillar and sill trim have tabs seated underneath seal.
  6. Remove RH C-pillar lower trim.
  7. Move RH seat to original position.
  8. Fold 2nd row RH seatback down.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Via seat switch or manual tether, and protect seat back upholstery if necessary.
  9. Remove RH seat outboard track cover.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Slide cover forward to release from RH seat track.
  10. Remove center track cover from 2nd row seats.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Slide covers forward to release from 2nd row seat tracks.
  11. Release cabin carpet from RH seat.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pull cabin carpet towards front of vehicle.
  12. Remove bolts securing RH seat podium to vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
    Informational PurposesAn informational icon, calling your attention
    Nota
    Discard bolts after removal.
  13. Move RH seat forward using towel bar.
    Informational PurposesAn informational icon, calling your attention
    Nota
    With one hand on towel bar pull up and slide the seat forward with your other hand.
  14. Remove bolts securing RH seat inner and outer tracks to vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Discard bolts after removal.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 11 mm
  15. Move RH seat fully rearward using towel bar.
    Informational PurposesAn informational icon, calling your attention
    Nota
    With one hand on towel bar pull up and slide the seat rearward with your other hand.
  16. Move 2nd row RH seatback to vertical position.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Via seat switch or manual tether, remove seatback protection if necessary.
  17. Disconnect 2nd row RH seat connector.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Newer models may have red locking tab.
  18. Remove RH seat from vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement.
  19. Remove RH seat toe kick cover.
  20. Remove clip securing RH seat side shield to cushion pan.
  21. Remove RH seat side shield from RH seat.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release rear side shield clip, then lift side shield upward to release hook from cushion pan.
  22. Remove RH 2nd row inboard outer B cover.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Pull inboard outer cover away from seat frame to remove.
  23. Fold RH seat into up position.
  24. Remove screw securing RH 2nd row inboard inner B cover to seat bottom.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25
  25. Disconnect 2nd row RH seat heater connector.
  26. Release 2nd row RH seat heater harness.
  27. Disconnect RH seat RH floor latch connector.
  28. Disconnect RH seat LH floor latch connector.
  29. Disconnect RH seatbelt buckle connector.
  30. Disconnect RH seat track position sensor connector.
  31. Disconnect seat heating connector.
  32. Release clips securing RH seat cushion harness to podium.
  33. Remove bolts securing RH seat cushion pan to seat frame.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm de cuello largo
  34. Remove clip securing RH seat cushion pan to seat frame.
  35. Release floor latch actuator.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  36. Slightly lift RH seat cushion pan upward.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lift RH seat cushion upward but do not fully remove at this time.
  37. Release RH seat easy entry actuator.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  38. Release RH seat actuator switch box.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  39. Disconnect RH seat occupancy sensor connector .
  40. Release RH seat occupancy sensor harness from cushion pan.
  41. Remove RH seat bottom harness.
  42. Remove RH seat cushion assembly from seat frame.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Lift cushion pan tabs upwards and remove seat cushion assembly.
  43. Remove RH seat cushion trim cover from cushion pan.
  44. Release Velcro securing RH seat cushion trim cover to foam pad.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release Velcro approximately 11 cm until hog rings are visible.
  45. Remove front hog rings securing RH seat cushion trim cover to foam pad.
  46. Release remaining velcro securing RH seat cushion trim cover to foam pad.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Release Velcro approximately 21 cm until hog rings are visible.
  47. Remove rear hooks securing RH seat cushion trim cover to foam pad and remove RH seat cushion trim cover.

Instalar

  1. Position RH seat cushion trim cover to foam pad and install rear hog rings securing RH seat cushion trim cover to foam pad.
  2. Install velcro securing RH seat cushion trim cover to foam pad.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Install Velcro approximately 21 cm.
  3. Install front hooks securing RH seat cushion trim cover to foam pad.
  4. Install remaing Velcro securing RH seat cushion trim cover to foam pad.
  5. Install RH seat cushion trim cover to cushion pan.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Properly route occupancy sensor harness and heat pad harness through cushion pan.
  6. Position RH seat cushion assembly to seat frame for installation.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Do not fully seat cushion assembly at this time.
  7. Install RH seat bottom harness.
  8. Install RH seat easy entry actuator.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  9. Install RH seat actuator switch box.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  10. Fully seat RH seat cushion assembly to seat frame.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Push downwards to full seat cushion pan to seat frame, and be cautious to not pinch actuator cables or cushion harness.
  11. Install floor latch actuator.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Dado de 8 mm
  12. Install RH seat occupancy sensor harness into cushion pan.
  13. Connect RH seat occupancy sensor connector.
  14. Install clip securing RH seat cushion pan to seat frame.
  15. Install bolts securing RH seat cushion pan to seat frame.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso de 10 mm
  16. Secure 2nd row RH seat heater harness.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Slide up to release.
  17. Connect 2nd row RH seat heater connector.
  18. Connect RH seat RH floor latch connector.
  19. Connect RH seat LH floor latch connector.
  20. Connect RH seatbelt buckle connector.
  21. Connect RH seat track position sensor connector.
  22. Connect seat heating connector.
  23. Install screw securing RH 2nd row inboard inner B cover onto seat bottom.
    1.5 Nm (1.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25
  24. Install RH 2nd row inboard outer B cover.
  25. Install RH seat side shield to RH seat.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Install side shield hook first, then secure clip.
  26. Install clip securing RH seat side shield to cushion pan.
  27. Install RH seat toe kick cover.
  28. Install RH seat into vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Recommend assistance, do not support RH seat by cushion pan, Support RH seat by podium.
  29. Connect 2nd row RH seat connector.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Newer models may have red locking tab.
  30. Install new bolts (X2) securing RH seat podium to vehicle hand tight.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25
  31. Move RH seat forward using towel bar.
    Informational PurposesAn informational icon, calling your attention
    Nota
    With one hand on towel bar pull up and slide the seat forward with your other hand.
  32. Install new bolts (X2) securing RH seat inner and outer tracks to vehicle.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Se recomienda utilizar las siguientes herramientas:
    • Vaso Torx T25
  33. Move RH seat to original position.
  34. Install cabin carpet to RH seat.
  35. Torque bolts securing RH seat podium to vehicle.
    37 Nm (27.3 lbs-ft)
  36. Install center track cover to 2nd row seats.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Slide cover straight on to clip to 2nd row seat tracks.
  37. Install RH seat outboard track cover.
  38. Position RH seat into easy entry mode.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Press shoulder switch and push RH seat forward to position into easy entry mode.
  39. Install RH rear sill trim.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips.
  40. Reseat RH rear door seal.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Seat pillar and sill trim tabs underneath seal.
  41. Move RH seat to original position.
  42. Move RH front seat to original position.
  43. Raise all four window.
  44. Ejecutar la rutina ODIN PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
  45. Ejecutar la rutina ODIN
  46. Ejecutar la rutina ODIN PROC_VCLEFT_X_2R-SEAT-RECLINE-CALIBRATIONvia Service Mode:Low Voltage ➜ Second Row Seats ➜ Calibratevia Toolbox:(link)
  47. Ejecutar la rutina ODIN PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  48. Close all four doors.