2026-04-30

ECU - Charge Port (7-Seat) (Remove and Replace)

Código de corrección TBD FRT 0.54 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Retirar

  1. Open all four doors and lower all windows.
  2. Open the hood via the touchscreen.
  3. Move the 1st row LH and RH seats forward.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Adjust the seat back to avoid contact with the headliner if needed.
  4. Open the liftgate.
  5. Press the shoulder switch and push the 2nd row seats forward to position the seats into the easy entry mode.
  6. Power off the vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Nota
    On the touchscreen, touch Controls > Safety > Power Off > Power Off.
  7. Remove the HEPA filter. See HEPA Filter Assembly (Remove and Replace).
  8. Remove the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) (Remove and Replace).
  9. Press the front switch at the LH trunk trim panel to release the 3rd row LH seat backrest.
  10. Press the rear switch at the LH trunk trim panel to release the 3rd row RH seat backrest.
  11. Disconnect the LV power. See LV Power (Disconnect and Connect) (Modify).
  12. Remove the rear load floor.
  13. Remove the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  14. Remove the LH trunk pocket bracket. See Compartimento - Lado izquierdo (7 plazas) (Desinstalación y sustitución).
  15. Release the remaining clips, and then remove the LH 7s trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x push clip, 2x clip tabs, 4x Guide tabs
  16. Release the LH trunk side trim and disconnect the 12V outlet connector.
    Informational PurposesAn informational icon, calling your attention
    Nota
    4x clips, 7x tabs, 1x connector
  17. Disconnect the charge port ECU connectors (x3).
  18. Remove the bolt that attaches the charge port ECU to the vehicle, and then slide the charge port ECU to the right, and then remove the charge port ECU from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    10mm

Instalar

  1. Install the charge port ECU by sliding it into the slots (x2) of the vehicle body, and then install the bolt that attaches the charge port ECU to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    Nota
    10mm, 9 Nm
  2. Connect the charge port ECU connectors (x3).
  3. Position the LH trunk side trim and install the lower clips.
    Informational PurposesAn informational icon, calling your attention
    Nota
    1x push clips, 5x clips,
    Informational PurposesAn informational icon, calling your attention
    Nota
    Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly. Guide the front clip stanchions around the LH C-pillar.
  4. Install the LH trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    Nota
    7x tabs, 4x clips, 1x location pin, 1x connector
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure the trunk seal is properly seated against the edge of the trim.
  5. Install the LH trunk pocket bracket. See Compartimento - Lado izquierdo (7 plazas) (Desinstalación y sustitución).
  6. Connect the LV power. See LV Power (Disconnect and Connect) (Modify).
  7. Install the 3rd row seat cushion. See Seat Cushion - 3rd Row (7-Seat) (Remove and Replace).
  8. Move the 1st row and 2nd row seats back to their original positions.
  9. Install the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  10. Raise the 3rd row RH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Manually raise the backrest up to its original position until it locks into place.
  11. Raise the 3rd row LH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Manually raise the backrest up to its original position until it locks into place.
  12. Install the rear load floor.
  13. Close the liftgate.
  14. Reinstall the vehicle firmware. See Reinstalación de software - Pantalla táctil.
  15. Raise all windows and close all doors.