2026-04-30

Body Harness - LH (7-Seat) (Remove and Install)

Código de corrección TBD FRT 2.7 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección y el FRT mencionados anteriormente reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento. NOTA: Consulte Precauciones ergonómicas para ver información sobre prácticas de trabajo seguras.

Aviso

Este procedimiento están en fase PRELIMINAR. Aunque se ha validado, es posible que falten advertencias y precauciones. Siga los requisitos de seguridad y tenga mucho cuidado cuando trabaje en sistemas y componentes de alta tensión o cerca de ellos.

2026-02-09: Released new procedure.

Open all four doors
Lower all four windows
Move LH front seat forward
Move RH front seat forward
Remove LH lower C-pillar trim

Nota
4x tabs, 3x clips, Release door seal as needed
Fold down 2nd row 60 seatback assembly

Nota
Press button, fold forwards
Disconnect 2nd row 60 seat connector

Nota
1x connector, Newer models may have red locking tab
Move 60 seat forward using towel bar

Nota
With one hand on towel bar pull up and slide the seat forward with your other hand
Remove 60 seat rear outboard track fastener

Nota
1x patch bolt, 11mm, 37 Nm, Discard after removal
Remove 60 seat rear inboard track fasteners

Nota
2x patch bolts, 11mm, 37 Nm, Discard after removal
Move 60 seat fully rearward using towel bar

Nota
With one hand on towel bar pull up and slide the seat forward with your other hand
Remove 60 seat outboard track cover

Nota
1x clip, Slide covers forward to release from 60 seat tracks
Remove center track cover from 2nd row seats

Nota
2x clips, Slide covers forward to release from 2nd row seat tracks
Release cabin carpet from 60 seat

Nota
Pull cabin carpet towards front of vehicle
Remove 60 seat front inboard track fasteners

Nota
1x bolts, 11mm, 37 Nm, Discard after removal
Remove 2nd row 60 seat frame front outboard track fasteners

Nota
1x bolts, 11mm, 37 Nm, Discard after removal
Remove 2nd row 60 seat assembly from vehicle

Nota
Recommend assistance, Note: If seat that is not being replaced does not have ISOFIX flag for child locks, the seat cover will also require replacement
Remove RH lower C-pillar trim

Nota
4x tabs, 3x clips, Release door seal as needed
Remove 40 seat outboard track cover

Nota
1x clip, Slide cover forward to release from 40 seat track
Release cabin carpet from 40 seat

Nota
Pull cabin carpet towards front of vehicle
Remove bolts securing 40 seat podium to vehicle

Nota
2x patch bolts, 11mm, 37 Nm, Discard bolts after removal
Fold 2nd row 40 seat down
Move 40 seat forward using towel bar

Nota
With one hand on towel bar pull up and slide the seat forward with your other hand
Remove bolts securing 40 seat inner and outer tracks to vehicle

Nota
2x patch bolts, 11mm, 37 Nm, Discard bolts after removal
Move 40 seat fully rearward using towel bar
Disconnect 2nd row 40 seat connector

Nota
1x connector, Newer models may have red locking tab
Remove 40 seat from vehicle

Nota
Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium
Remove 3rd row seat cushion and disconnect harness

Nota
1x connector, Pull LH and RH release lever under 3rd row seat cushion to release seat cushion
Open liftgate
Release 3rd row LH seat backrest

Nota
Front switch at LH trunk trim panel
Release 3rd row RH seat backrest

Nota
Rear switch at LH trunk trim panel
Remove rear load floor
Remove trunk sill trim

Nota
4x clips
Remove LH load floor bracket

Nota
6x tabs
Release remaining clips and remove LH 7s trunk side trim

Nota
1x push clip, 2x clip tabs, 4x Guide tabs
Release LH 7s trunk side trim and disconnect 12V outlet

Nota
4x clips, 7x tabs, 1x connectors
Remove LH upper C-pillar trim

Nota
2x tabs, 5x clips, 1x location pin
Remove RH load floor bracket

Nota
6x tabs
Remove RH trunk pocket bracket

Nota
1x push clip, 2x clip tabs, 4x Guide tabs
Release top edge of RH trunk side trim

Nota
4x clips, 7x tabs, 1x connectors
Remove RH upper C-pillar trim

Nota
6x clips, Guide front upper corner groove out from headliner and place trim aside, trim part may slightly differ by vehicle build location, and the number of clips may also varyt
Remove LH mid A pillar assembly

Nota
1x clip, 1x tab, Release upper clip then pull mid A pillar upward to remove
Remove clip securing LH lower A pillar trim

Nota
1x push clip
Remove LH lower A pillar trim

Nota
6x clips, 2 guide tabs, Pull rear of lower A pillar upward to release clip then pull rearward to release trim panel
Partially release LH front primary door seal
Remove RH mid A pillar assembly

Nota
1x clip, 1x tab, Release the upper clip then pull mid A pillar upward to remove
Remove clip securing RH lower A pillar trim

Nota
1x push clip
Remove RH lower A pillar trim to release seat harness.

Nota
6x clips, 2 guide tabs, Pull rear of lower A pillar upward to release clip then pull rearward to release trim panel
Partially release RH front primary door seal
Release RH front seat belt retractor from pretensioner

Nota
Insert special removal tool into the bottom of the retractor to release
Release LH front seat belt retractor from pretensioner

Nota
Insert seat belt tool into the bottom of the retractor to release
Remove LH front seat rear fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Move LH front seat backward

Nota
Ensure profile is saved to allow seat position to be restored
Remove LH front seat front fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Adjust position of LH front seat for easy removal

Nota
Move seat to middle of track at most upright position
Remove RH front seat rear fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Move RH front seat backward
Remove RH front seat front fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Adjust position of RH front seat for easy removal

Nota
Move seat to middle of track at most upright position
Open hood
Remove rear apron

Nota
14x clips
Power off vehicle from center display

Nota
Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
Disconnect LV battery and first responder loop

Nota
2x tabs, 2x connectors, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting Disconnect LV battery and first responder loop, Ensure that one minute has passed after window movement before performing the power-off, Battery should be disconnected before Firefighter line, Allow 2 minutes for all electrical circuits to fully discharge
Disconnect LH front seat harness from VC left

Nota
1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC left, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged
Remove LH front seat harness clips from LH footwell support bracket

Nota
2x retaining clips
Release LH front seat harness from LH front sill panel harness bracket

Nota
5x clips
Pull LH front seat harness from under LH front cabin carpet
Remove LH front seat from vehicle

Nota
Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
Disconnect RH front seat harness from VC right

Nota
1x electrical connector, Release the lock by squeezing the release tab, Then fully disengage the lock by moving it away from the VC right, Do not force the connector, If the connector does not easily release from the VC the lock is still engaged
Remove RH front seat harness from RH footwell support bracket

Nota
2x retaining clips
Release RH front seat harness from lower A 12V bracket

Nota
5x clips
Pull RH front seat harness from under RH front cabin carpet
Remove RH front seat from vehicle

Nota
Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim
Remove console lower rear panel

Nota
6x tabs
Remove LH center console carpet covers

Nota
2x covers, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
Remove LH exterior hardware from center console

Nota
3x bolt, 10mm, 7 Nm
Remove RH center console side panel carpets

Nota
2x covers, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
Remove RH exterior hardware from center console

Nota
3x bolts, 10mm, 7 Nm
Disconnect harness from rear of center console

Nota
1x connector
Disconnect USB harness at right front of center console

Nota
1x USB connector
Remove center console from vehicle

Nota
Recommend assistance, Tilt rear of console upward, pull assembly towards rear of vehicle, then tilt front of console upward and remove through passenger side
Release LH upper B pillar assembly and move aside

Nota
4x tabs, 5x retainers, Unhook retainers from body while pulling the bottom of the upper B pillar, then pull the top to release the remaining clips
Remove clip securing LH lower B-pillar to body

Nota
1x push clip, Clip secures lower B-pillar and rear cabin carpet to body
Remove LH lower B pillar assembly

Nota
6x clips, Pull the top of B pillar to release top clips then work your way to bottom clips
Release clips securing RH upper B-pillar assembly and move aside

Nota
4x tabs, 5x retainers, Unhook retainers from body while pulling the bottom of the upper B pillar, then pull the top to release the remaining clips
Remove clip securing RH lower B-pillar to body

Nota
1x push clip, Clip secures lower B-pillar and rear cabin carpet to body
Remove RH lower B-pillar assembly

Nota
6x clips, Pull the top of B-pillar to release top clips then work your way to bottom clips
Remove rear floormat
Remove OBD2 female connector from LH footwell cover and release carpet

Nota
1x connector, 2x push clips, Press lateral tabs and pull harness to release from carpet, remove push clips to release LH front carpet
Remove fasteners securing driver knee air bag to vehicle

Nota
4x patch bolts, E10, 8 Nm, Discard after removal, Support the knee air bag while lowering, The connector / harness length is very short
Remove LH front cabin carpet from vehicle

Nota
Lift up rear edge of carpet then slide out towards rear of vehicle, be cautious and avoid foam below catching on seat risers
Remove LH upper A-pillar trim

Nota
3x clips, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove
Remove LH sun visor bracket cover

Nota
4x clips, Extending the sun visor may allow for extra working room
Unfasten LH sun visor

Nota
1x fastener, Torx T25
Remove LH sun visor from headliner area

Nota
1x connector, Hinge sun visor downward and away from headliner, Disconnect sun visor harness
Remove RH upper A-pillar trim

Nota
3x clips, Pull inside of the upper portion of upper A-pillar, Remove 3x tether hooks by twisting and pulling away from housing, Then pull upper A-pillar upward to remove
Remove RH sun visor bracket cover

Nota
4x clips, Extending the sun visor may allow for extra working room
Unfasten RH sun visor

Nota
1x fastener, Torx T25
Remove RH sun visor from headliner area

Nota
1x connector, Hinge sun visor downward and away from headliner, Disconnect sun visor harness
Push open LH coat hook
Open LH coat hook screw cover

Nota
1x locking tab
Remove LH coat hook screw

Nota
1x screw, T20, 1.0 Nm
Push open RH coat hook
Open RH coat hook screw cover

Nota
1x locking tab
Remove RH coat hook screw

Nota
1x screw, T20, 1.0 Nm
Release headliner from body

Nota
3x clips, 3 location pins, 2x magnets, 2x interlocking clips, recommend assistance, Headliner will be partially supported by safety tethers at B-pillars and 2x tether clips at rear corners
Disconnect J5 body connector

Nota
1x connector, Release lock then remove
Disconnect J2 body connector

Nota
1x connector, Release lock then remove
Disconnect J4 body connector

Nota
1x connector, Release lock then remove
Disconnect headliner harness

Nota
1x connector
Disconnect white connector X909 from front harness

Nota
1x connector
Remove LH body harness clips from LH A-pillar

Nota
3x clips
Release LH body harness from below LH front seat

Nota
1x push tabs, press tabto release harness guide clips from body frame.
Remove LH harness clips under front seats and center console

Nota
3x clips
Disconnect LH body harness from RCM

Nota
1x connector
Disconnect LH harness from RH body Harness

Nota
2x connectors,1x clip,Release red locking tabs
Disconnect the LH body harness connectors around lower B-pillar area

Nota
4x connectors, LH rear door harness, acceleration sensor, and LH seat belt
Remove the LH harness ground strap around LH lower B-pillar area

Nota
1x bolt, 10mm, 10 Nm
Remove LH harness clips from B-pillar area

Nota
6x clips
Remove LH B-pillar applique from body

Nota
2x clips, 2x connectors, Pull straight outwards to release from B-Pillar, disconnect camera connector then remove from vehicle, Use caution not to damage the connectors
Remove the LH body harness around the below C-pillar area

Nota
1x location point holes, 1x clip
Disconnect LH 2nd row retractor connector

Nota
1x connector, pull both orange side tabs simultaneously to remove harness
Remove the LH body harness clips around C-pillar area

Nota
4x clips
Disconnect LH side curtain air bag and liftgate power strut electrical connector from LH body harness

Nota
2x connectors
Release connectors from LH body harness to charge port ECU

Nota
2x connectors
Remove LH body harness clips around LH side trunk area

Nota
3x clips
Disconnect connectors from chargeport assembly

Nota
2x connectors, 1x red locking tab, 1x white locking tab
Remove the LH body harness ground strap below LH tail lamp

Nota
1x bolt, 10mm, 10 Nm
Remove LH liftgate stop

Nota
1x liftgate stop, Pull up to remove
Remove bolt securing LH corner of rear fascia to body

Nota
1x bolt, 10mm, 4 Nm
Remove RH liftgate stop

Nota
1x liftgate stop, Pull up to remove
Remove bolt securing RH corner of rear fascia to body

Nota
1x bolt, 10mm, 4 Nm
Release rear diffuser from vehicle

Nota
6x clips, 6x bolts, 2x fasteners, 8mm, 10mm, Torx T20, 4 Nm
Remove LH rear fender garnish from vehicle

Nota
12x clips, Release from center of garnish and work your way outward towards both ends
Remove bolts securing LH rear fascia to body

Nota
2x bolts, 8mm, 10mm, 4 Nm
Remove RH rear fender garnish from vehicle

Nota
14x clips,
Remove bolts securing RH rear fascia to body

Nota
2x bolts, 8mm, 10mm, 4 Nm
Remove Fasteners securing rear diffuser to body

Nota
2x fasteners, Torx T20
Release rear fascia from body

Nota
Pull fascia away from vehicle to release fully
Remove rear body harness from rear fascia center bracket

Nota
1x clips, located behind LH side connector
Disconnect rear subframe and LH rear EPB connectors

Nota
2x connectors
Push the rear subframe portion of the LH body harness through the LH side trunk bulkhead

Nota
Harness passes through into trunk near rear section of LH rear wheel liner area
Remove LH body harness
Position LH body harness
Push the rear harness seal through body and fully seat

Nota
Harness passes through into trunk near rear section of LH rear wheel liner area
Connect rear subframe and LH rear EPB connector

Nota
2x connectors
Install rear body harness onto rear fascia center bracket

Nota
1x clips
Connect and install rear fascia onto vehicle

Nota
1x connector, Engage red locking tab, Recommend assistance, Verify lower portion aligns with rear diffuser.
Install rear diffuser onto vehicle

Nota
6x clips, 6x bolts, 2x fasteners, 8mm, 10mm, Torx T20, 4 Nm, Apply Loctite 222 onto rear diffuser bolts and secure rear fascia to rear diffuser
Install fasteners securing rear diffuser to body

Nota
2x fasteners, Torx T20
Install bolt securing RH rear fascia to body

Nota
2x bolt, 8mm, 10mm, 4 Nm
Install RH rear fender garnish

Nota
14x clips, Insert front of garnish into vehicle first, then push garnish clips into vehicle
Install bolt securing LH rear fascia to body

Nota
2x bolt, 8mm, 10mm, 4 Nm
Install LH rear fender garnsih

Nota
14x clips,
Install bolt securing RH corner of rear fascia

Nota
1x bolt, 10mm, 4 Nm
Install RH liftgate stop

Nota
1x liftgate stop, Align tab and push down to secure
Install bolt securing LH corner of rear fascia

Nota
1x bolt, 10mm, 4 Nm
Install LH liftgate stop

Nota
1x liftgate stop, Align tab and push down to secure
Install the LH body harness ground strap below LH tail lamp

Nota
1x bolt, 10mm, 10 Nm
Install logic connectors to charge port assembly

Nota
3x connectors, 1x red locking tab, 2x white locking tab
Install LH body harness clips around LH side trunk area

Nota
3x clips
Install connectors from LH body harness to charge port ECU

Nota
2x connectors
Connect LH side curtain air bag and liftgate power strut electrical connector to LH body harness

Nota
2x connectors
Install the LH body harness clips around upper C-pillar area

Nota
4x clips
Connect LH 2nd row retractor connector

Nota
1x connector,
Install the LH body harness clips around the below C-pillar area

Nota
2x clips, 1x location insert
Install LH B-pillar applique to vehicle

Nota
2x connectors, 1x fir tree clip, 2x clips, Align B-Pillar applique into position and secure clips into body, Use caution not to damage the connectors
Install LH harness clips onto B-pillar area

Nota
6x clips
Connect the LH body harness connectors around lower B-pillar area

Nota
4x connectors, LH rear door harness, acceleration sensor, and LH seat belt
Install the LH harness ground strap around LH lower B-pillar area

Nota
1x bolt, 10mm, 10 Nm
Connect LH harness to RH body Harness

Nota
2x connector,1x clip,Engage locking tabs
Install LH body harness to RCM

Nota
1x connector
Install LH harness clips under LH front seat and RH lower B-pillar area

Nota
3x clips
Install LH body harness below LH front seat

Nota
3x tabs, insert tabs into position and ensure proper installation with push pull test.
Install LH body harness clips to LH A-pillar

Nota
3x clips
Connect J5 body connector

Nota
1x connector, Fully seat connector then engage lock
Connect J2 body connector

Nota
1x connector, Fully seat connector then engage lock
Connect J4 body connector

Nota
1x connector, Fully seat connector then engage lock
Connect white connector X909 to front harness

Nota
1x connector
Connect headliner harness

Nota
1x connector
Install driver knee air bag

Nota
1x connector, Use caution not to damage connector/harness, Support air bag while connecting connector
Install fasteners securing driver knee air bag to vehicle

Nota
4x patch bolts, E10, 8 Nm, Install new patch bolts
Install headliner to body

Nota
11x clips, Recommend assistance, Seat 2x clips at coat hooks when replacing headliner, Reseat primary seal at doors and liftgate to headliner
Connect RH sun visor connector

Nota
1x connector
Install RH sun visor into headliner area

Nota
Fold sun visor to the closed and folded down position but do not latch in place
Install RH sun visor fastener

Nota
1x screw, T25, 3.5 Nm
Install RH sun visor bracket cover

Nota
4x clips
Install RH upper A-pillar trim

Nota
3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
Connect LH sunvisor connector

Nota
1x connector
Install LH sun visor into headliner area

Nota
Fold sun visor to the closed and folded down position but do not latch in place
Install LH sun visor fastener

Nota
1x screw, T25, 3.5 Nm
Install LH sun visor bracket cover

Nota
4x clips
Install LH upper A-pillar trim

Nota
3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
Install LH coat hook screw

Nota
1x screw, T20, 1.0 Nm
Close LH coat hook screw cover

Nota
1x locking tab
Push LH coat hook closed
Install RH coat hook screw

Nota
1x screw, T20, 1.0 Nm
Close RH coat hook screw cover

Nota
1x locking tab
Push RH coat hook closed
reconnect 3rd row seat recliner connector and install LH upper C-pillar trim

Nota
4x clips, 2x tabs, 1x Connector, 1x Emergency release, Guide front upper corner groove under headliner, Insert guide tab to headliner behind quarter glass, Seat trunk seal to edge of trim
Install LH 7s trunk side trim

Nota
7x tabs, 4x clips, 1x location pin, 1x connector, Ensure to seat trunk seal to edge of trim
Install LH trunk pocket bracket

Nota
2x retainer clips, 4x alignment tabs
Install LH load floor bracket

Nota
6x clips
Install RH upper C-pillar trim

Nota
2x tabs, 4x clips, 1x connector, Seat trunk seal to edge of trim
Install RH trunk side trim

Nota
7x tabs, 4x clips, 1x location pin, Ensure to seat trunk seal to edge of trim
Install RH trunk pocket bracket

Nota
1x push clip, 5x alignment tabs
Install RH load floor bracket

Nota
6x tabs, Confirm each installation with push-pull test
Install rear load floor
Install trunk sill trim

Nota
4x clips, Seat seal around edge of trim
Install rear main cabin carpet to vehicle

Nota
Position rear main carpet to floorboard and slide forward, Ensure rear main carpet tucks beneath front main carpet and air duct
Install rear floormat
Install LH front cabin carpet

Nota
1x connector, Install OBD connector into LH front carpet footwell cover
Install clips securing LH front cabin carpet to vehicle

Nota
2x push clips
Install 2nd row 60 seat assembly

Nota
Recommend assistance
Connect 2nd row 60 seat connector

Nota
1x connector, Newer models may have red locking tab
Install fasteners securing 60 seat frame to body

Nota
5x patch bolts, 11mm, 37 Nm, Install new patch bolts, bottom seat bolts located in rear
Secure cabin carpet to 60 seat

Nota
Strap velcro on
Move 2nd row 60 seatback to vertical position

Nota
Remove seat back protection if necessary
Install 60 seat outboard track cover

Nota
1x clip
Install 40 seat into vehicle

Nota
Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium
Connect 2nd row 40 seat connector

Nota
1x connector, Newer models may have red locking tab
Install bolts securing 40 seat podium to vehicle hand tight

Nota
2x patch bolts, 11mm, 37 Nm, Install new bolts, Torque at later step
Move 40 seat forward using towel bar

Nota
With one hand on towel bar pull up and slide the seat forward with your other hand
Install bolts securing 40 seat inner and outer tracks to vehicle

Nota
2x patch bolts, 11mm, 37 Nm, Install new bolts
Move 40 seat to original position
Torque bolts securing 40 seat podium to vehicle

Nota
2x patch bolts, 11mm, 37 Nm
Install cabin carpet to 40 seat
Install center track cover to 2nd row seats

Nota
2x clip, Slide cover straight on to clip to 2nd row seat tracks
Install 40 seat outboard track cover

Nota
1x clip
Install 3rd row seat cushion and connect harness

Nota
1x connector, Secure 3rd row seat cushion into RH and LH latches
Install RH upper B-pillar assembly

Nota
4x tabs, 5x retainer tabs, Lower seat belt slider to align with B pillar panel, Insert top portion of upper B pillar under headliner to align clips, Spread bottom of trim assembly to properly seat upper B pillar, ensure seal correctly overlaps trim
Install RH lower B-pillar assembly

Nota
7x clips, 2x tabs, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips
Install clip securing RH lower B-pillar to body

Nota
1x push clip, Clip goes through B-pillar and rear cabin carpet
Install RH lower C-pillar trim

Nota
4x tabs, 3x clips, Secure door seal as needed
Install LH upper B pillar assembly

Nota
4x tabs, 5x retainer tabs, Lower seat belt slider to align with B pillar panel, Insert top portion of upper B pillar under headliner to align clips, Spread bottom of trim assembly to properly seat upper B pillar, ensure seal correctly overlaps trim
Install LH lower B pillar assembly

Nota
7x clips, 2x tabs, Align the bottom guide tab to its slot then press the bottom clips, Work your way to top clips
Install clip securing LH lower B pillar to body

Nota
1x push clip, Clip secures lower B pillar and rear cabin carpet to body
Install LH lower C-pillar trim

Nota
4x tabs, 3x clips, Secure door seal as needed
Install center console onto vehicle

Nota
Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into position
Connect harness at right front of center console

Nota
1x USB connector
Connect harness to rear of center console

Nota
1x connector
Install RH front exterior hardware to center console

Nota
2x bolts, 10mm, 7 Nm, The relatively newer vehicles are equipped with a T30 bolt.
Install RH console side panel carpet

Nota
2x covers,
Install LH console side panel carpet

Nota
10x clips, 1x guide pin, Position side panel and align the locator, then the rear locator, Push side panel towards console to install
Install console lower rear panel

Nota
5x clips
Install LH front seat into vehicle

Nota
Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim, Gateway configuration update for cfg_frontSeattype is needed when replacing from 7654322-XX-E to 7654322-XX-F or newer 1st Row LHD LH Seat Assembly with 1st Row Mini-Tilt Motor Assembly
Secure LH front seat harness under LH front cabin carpet
Install LH front seat harness along LH front sill panel harness bracket

Nota
5x clips
Install LH front seat harness clips onto LH footwell support bracket

Nota
2x retaining clips
Connect LH front seat harness to VC left

Nota
1x electrical connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated
Install LH lower A pillar trim

Nota
6x clips, 2 locating pins, Align front locating pin first
Install clip securing LH lower A pillar trim

Nota
1x push clip
Install LH mid A pillar assembly

Nota
1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A pillar, Pull seal over trim
Reseat LH front door seal along lower A pillar trim
Install RH front seat into vehicle

Nota
Recommend assistance, Assistant should be ready to support seat back, Caution not to damage any trim, Gateway configuration update for cfg_frontSeattype is needed when replacing from 7654324-XX-C to 7654324-XX-F or newer 1st Row LHD RH Seat Assembly with 1st Row Mini-Tilt Motor Assembly
Secure RH front seat harness under RH front cabin carpet
Install RH front seat harness along plastic guide

Nota
5x clips
Install RH front seat harness onto RH footwell support bracket

Nota
2x retaining clips
Connect RH front seat harness to VC right

Nota
1x connector, Ensure the connector and lock are fully engaged, Perform pull push pull test to ensure the connector and connector lock are seated
Install RH lower A pillar trim

Nota
6x clips, 2x locating pins, Align front locating pin first
Install clip securing RH lower A pillar trim

Nota
1x push clip
Install RH mid A pillar assembly

Nota
1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A pillar, Make sure the seal seat on top of the trim
Reseat RH front door seal along lower A pillar trim
Connect first responder loop and battery

Nota
2x connectors, engage locking tabs, Connect FRL first before connecting 12V to avoid damage to car computer
Install rear apron

Nota
14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
Close hood
Move LH front seat backward
Install LH front seat front fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move LH front seat forward
Install LH front seat belt retractor to quick fix

Nota
Slide the linkage into quick fix, an audible click will be heard, Verify there are no twists in the webbing from the upper trim to quick fix, Perform a firm pull test to confirm pretensioner is engaged
Install LH front seat rear fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move LH front seat to original position
Move RH front seat backward
Install RH front seat front fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH front seat forward
Install RH front seat belt retractor to pretensioner

Nota
Slide the linkage onto the pretensioner cable, an audible click will be heardVerify there are no twists in the webbing from the upper trim to the pretensionerperform a firm pull test to confirm pretensioner is engaged
Install RH front seat rear fasteners

Nota
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH front seat to original position
Close liftgate
Raise all four windows
Close all four doors

Nota
If LV is powered up, Unlatch rear doors before closing

Body Harness - LH (7-Seat) (Remove and Install)

Figura 1

Figura 2

Figura 3