23/04/2024 17:36:47

Headlights - Adjust - NA (Tool Method)

Código de corrección 174000150 FRT NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Adjust Headlights Using a Headlight Tester

Special tools required for this procedure:

Supplier Part Number Description
Tesla 1133367-00-A HEADLIGHT TESTER, BEISSBARTH, MLD 815
  1. Open the LH front door and lower LH front window.
  2. Open the front trunk hood.
  3. Place the vehicle in Service Mode via touchscreen. See Modo de servicio.
  4. On the vehicle touchscreen, enter headlight adjustment mode: Controls > Service > Adjust Headlights.
  5. Turn on the headlights.
  6. Position the headlight tester tool ~11 in. (30 cm) from the front of the LH headlight lens.
  7. Adjust the height of the headlight tester tool to ~20.4 in. (68 cm) above the ground to align with the center point of the headlamp.
  8. Connect the headlight tester tool to an electrical outlet, and then turn on the headlight tester tool.
  9. Adjust the knobs on the base of the headlight tester tool until the tool is leveled, as indicated by the bubble gauge on the tool.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The bubble must be entirely inside of the center ring in order to properly align the headlights.
  10. Turn on the alignment laser near the top of the tool, and then rotate the tool as necessary to align the laser with the base of both hood struts.
    Figura 1. LH Hood Strut
  11. On the headlight tester tool, select Test US, then select >Free Test.
  12. On the headlight tester tool, select Headlight, and then use the + or - buttons to change the Headlight type to "SAE".
  13. On the headlight tester tool, select Light, and then use the + or - buttons to change the Light type to LED.
  14. On the headlight tester tool, select Inclina., and then use the + or - buttons to set the inclination.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Inclination information is located on the headlight.
  15. On the headlight tester tool, select Height, and then + or - buttons to adjust to68CM.
  16. On the headlight tester tool, select OK.
  17. On the headlight tester tool, select OK again to proceed past fog light settings.
  18. On the headlight tester tool, select Laser to turn on the headlight laser guide.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Use of a flashlight can aid in finding marks, and shift vertical beam outboard 66mm from marking to properly align with light output.
  19. On the headlight tester tool, select Left low beam, and then select Low beam near the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
  20. On the steering wheel, select Left and then use the left scroll wheel to adjust the beam level: Target 0.00" +/- 1.0"
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Do not sit in the vehicle, as this will affect headlight alignment.
    Informational PurposesAn informational icon, calling your attention
    Nota
    There might be a delay between the scroll wheel input and actual headlight adjustment output.
  21. On the headlight tester tool, select Save to record the results.
  22. Roll the headlight tester tool to the RH headlight, and then position the tool ~30 cm from the front of the RH headlight lens.
  23. On the headlight tester tool, select Right low beam, and then select Low beam near the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure that High beam is not selected.
    Informational PurposesAn informational icon, calling your attention
    Nota
    The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
  24. On the steering wheel, select Right and then use the right scroll wheel on the steering wheel to adjust the beam level: Target 0.00" +/- 1.0"
    Warning IconA warning icon, calling your attention to a possibly risky situation
    PRECAUCIÓN
    Do not sit in the vehicle while using the scroll wheel as this will affect headlight alignment.
    Informational PurposesAn informational icon, calling your attention
    Nota
    There might be a delay between the scroll wheel input and actual headlight adjustment output.
  25. On the headlight tester tool, select Save to record the results.
  26. On the headlight tester tool, select Save again to view test results.
  27. Close the front trunk hood.
  28. Raise LH front window.
  29. Close LH front door.