19/01/2024 18:14:43

Hose - Inlet - Front Drive Unit Inverter (Remove and Replace)

Código de corrección 1830020162 FRT 0.60 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Retirar

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect the LV power. See LV Battery - Li-lon (Disconnect and Connect).
  4. Remove the cabin intake duct. See Assembly - Fresh Air Gutter - HVAC (Remove and Replace).
  5. Remove the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  6. Remove the push clips (x3) and bolt that attaches the RH front wheel arch liner to the skid plate.
  7. Use a bungee strap to pull back the RH front wheel arch liner and secure it to the subframe.
  8. Position a coolant drain container underneath the RH front of the HV battery.
  9. Release the clip, disconnect the powertrain return hose from the front drive unit inverter inlet hose, and then immediately plug both fittings.
  10. Position a coolant drain container underneath the LH rear of the front drive unit.
  11. Release the clip, disconnect the front drive unit inverter inlet hose from the front drive unit, and then immediately plug both fittings.
  12. Use a clip prytool to release the clip that attaches the front drive unit inverter inlet hose to the front subframe.
  13. Use a clip prytool to release the clip that attaches the front drive unit inverter inlet hose to the front drive unit.
  14. Remove the front drive unit inverter inlet hose.

Instalar

  1. Install the clip that attaches the front drive unit inverter inlet hose to the front drive unit.
  2. Install the clip that attaches the front drive unit inverter inlet hose to the front subframe.
  3. Remove the plugs from the fittings, immediately connect the front drive unit inverter inlet hose to the front drive unit inverter, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  4. Remove the plugs from the fittings, immediately connect the front drive unit inverter inlet hose to the powertrain return hose, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  5. Remove the coolant drain collector from under the vehicle.
  6. Remove the bungee strap from the RH front wheel arch liner.
  7. Install the push clips (x3) and bolt that attaches the RH front wheel arch liner to the skid plate.
  8. Install the front aero shield panel. See Panel - Aero Shield - Front (Remove and Replace).
  9. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  10. Perform the cooling system (partial refill and bleed) procedure. See Sistema de refrigeración (Llenado parcial y purga).
  11. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  12. Remove the vehicle from the 2 post lift. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.