2026-08-19

Detección de fugas de refrigerante del aire acondicionado

Código de corrección 00100004 Adjustable FRT (General Diagnosis) NOTA: Registre todo el tiempo y el trabajo empleados en el diagnóstico del sistema de aire acondicionado utilizando el código de corrección 00100004. No añada Refrigerante del aire acondicionado (Recuperación y recarga) a la actividad. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Protección personal to make sure wearing proper PPE when performing the below procedure. NOTE: See Precauciones ergonómicas for safe and healthy working practices.

  • 2026-08-10: Updated correction code guidance.
Equipo:
  • 1711245-00-A Snap On Ecotechnics Dual Gas AC Machine
  • 1501412-00-A Mastercool R1234YF Oil Injector
  • 1076971-02-A Torque Wrench ¼ in Dr. +Angle
  • 1060071-00-A Torque Wrench ¼ in Dr Hexagon
Nota
Para poder realizar este procedimiento, debe haberse realizado el de Refrigerante del aire acondicionado (Recuperación y recarga). Si no se ha hecho automáticamente, añada el código de corrección 18200102 como una corrección independiente dentro de la misma actividad de la visita de servicio.

Conectar Procedimiento

  1. Set up the A/C machine.
  2. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  3. Unlock the vehicle gateway. See Desbloqueo de la puerta de enlace.
  4. On the touchscreen, touch Service Mode > Thermal > Refrigerant System > Start Refrigerant Fill/Drain and select Run to start the "Start Thermal Fill Drain (Refrigerant Only)" routine.
  5. Recover the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge) (Restore).
  6. Perform the vacuum leak test and refill A/C refrigerant. See A/C Refrigerant (Recovery and Recharge) (Restore).
  7. Add 5 ml UV dye.
    Nota
    Add the dye with the refrigerant and oil.
  8. Remove the A/C hoses from the vehicle.
  9. On the touchscreen, touch Thermal > Refrigerant System > Run Heat Pump Commissioning and select Run to start the routine.
  10. Touch Thermal > Actions > Test Thermal Performance and select Run to start the routine.
    Nota
    Make sure the routine is passed, then touch Close to close it.
  11. Touch Thermal > Actions > Test HVAC Performance and select Run to start the routine.
    Nota
    Make sure the routine is passed, then touch Close to close it.
  12. Exit Service Mode through UI. See Modo de servicio.
  13. Set the temperature to LO on both driver and passenger HVAC controls and set the A/C system to AUTO.
  14. Run the A/C system for 10 minutes to allow the dye to circulate.
  15. Use UV light and the UV inspection kit to check for A/C refrigerant leaks near the HVAC end of the Supermanifold to HVAC A/C line.
    Nota
    If an A/C refrigerant leak is found, replace the A/C line from supermanifold to HVAC. See Assembly - A/C Line - Supermanifold to HVAC (Remove and Replace).
  16. Use UV light and the UV inspection kit to check for A/C refrigerant leaks at the A/C low and high pressure port.
    Nota
    If an A/C refrigerant leak is found, replace the A/C line from supermanifold to HVAC. See Assembly - A/C Line - Supermanifold to HVAC (Remove and Replace).
  17. Use UV light and the UV inspection kit to check for A/C refrigerant leaks at the supermanifold area.
    Nota
    If an A/C refrigerant leak is found, replace the defective component.
  18. Use UV light and the UV inspection kit to check for A/C refrigerant leaks on the A/C compressor discharge and suction lines area.
    Nota
    If an A/C refrigerant leak is found, replace the supermanifold to compressor A.C line. See Assembly - A/C Line - Supermanifold to Compressor (Remove and Replace).
  19. Use UV light and the UV inspection kit to check for A/C refrigerant leaks on the supermanifold.
    Nota
    If an A/C refrigerant leak is found, replace the defective component.
  20. Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace)
  21. Use UV light and the UV inspection kit to check for A/C refrigerant leaks near the Supermanifold end of the Supermanifold to HVAC A/C line.
    Nota
    If an A/C refrigerant leak is found, replace the A/C line from supermanifold to HVAC. See Assembly - A/C Line - Supermanifold to HVAC (Remove and Replace).
  22. Install the front aero shield. See Panel - Aero Shield - Front (Remove and Replace)
  23. Install the caps (x2) back onto the A/C ports.
  24. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).