19/01/2024 18:14:02

Hose - Inlet - Rear Drive Unit Inverter (Remove and Replace)

Código de corrección 1830020032 FRT 0.66 NOTA: Salvo que se indique lo contrario explícitamente en el procedimiento, el código de corrección anterior y el FRT reflejan todo el trabajo necesario para realizar este procedimiento, incluidos los procedimientos vinculados. No acumule códigos de corrección a menos que se le indique explícitamente que lo haga. NOTA: Consulte Tiempos de tarifa plana para obtener más información sobre los FRT y cómo se crean. Para enviar sus comentarios sobre los valores de FRT, escriba a LaborTimeFeedback@tesla.com. NOTA: Consulte Protección personal para asegurarse de llevar el EPI adecuado al realizar el siguiente procedimiento.

Retirar

  1. Raise and support the vehicle. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.
  2. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  3. Disconnect the LV power. See LV Battery - Li-lon (Disconnect and Connect).
  4. Remove the rear aero shield panel. See Panel - Aero Shield - Rear (Remove and Replace).
  5. Remove the rear skid plate. See Skid Plate - HV Battery - Rear (Remove and Replace).
  6. Position a coolant drain container underneath the LH rear of the HV battery.
  7. Release the clip, disconnect the rear drive unit inverter inlet hose from the HV battery, and then immediately plug both fittings.
  8. Release the clip, disconnect the rear drive unit inverter inlet hose from the rear drive unit inverter, and then immediately plug both fittings.
  9. Release the clip that attaches the rear drive unit inverter inlet hose to the rear drive unit HV harness.
  10. Remove the rear drive unit inverter inlet hose down and out from between the rear subframe and the HV battery.

Instalar

  1. Install the rear drive unit inverter inlet hose in and up between the rear subframe and the HV battery.
  2. Fasten the clip that attaches the rear drive unit inverter inlet hose to rear drive unit HV harness.
  3. Remove the plugs from the fittings, immediately connect the rear drive unit inverter inlet hose to the rear drive unit inverter, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  4. Remove the plugs from the fittings, immediately connect the rear drive unit inverter inlet hose to the HV battery, fasten the clip, and then perform a Push-Pull-Push check of the fitting.
  5. Remove the coolant drain collector from under the vehicle.
  6. Install the HV battery rear skid plate. See Skid Plate - HV Battery - Rear (Remove and Replace).
  7. Install the rear shield panel. See Panel - Aero Shield - Rear (Remove and Replace).
  8. Connect LV power. See LV Battery - Li-lon (Disconnect and Connect).
  9. Remove the coolant bottle cap, and then fill the coolant to the proper level.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure that the coolant level is at the "Max" line.
  10. Connect the vehicle to a laptop with Toolbox 3.0. See Toolbox 3 (Conexión y desconexión).
  11. In Toolbox 3.0, click Actions/Autodiag, type "Purge" into the search field, click TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGE, click Run, and allow the routine to complete.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Make sure vehicle is not in Drive, shifting the vehicle into Drive will stop this routine. The test will last approximately 10 mins. The test will vary speeds from 3500-6500 RPM (idle speed = ~1500 RPM) and actuate the valve between series and parallel. If speed hovers at 7000 RPM, it indicates the pump is air locked, perform the vacuum fill again. Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle.
  12. Inspect the coolant level and top off as necessary, and then install the coolant bottle cap.
    Informational PurposesAn informational icon, calling your attention
    Nota
    Ensure that the coolant level is at the "Max" line.
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  14. Remove the vehicle from the 2 post lift. See GUID-0ECF2493-88F6-48E9-ADBB-9AE1D52E217C.html.